Video |
Switcher |
2x1 manual or auto-switching, audio-follow-video |
Input Signal Types |
HDMI w/Deep Color, 3D, & 4K (DVI & Dual-Mode DisplayPort compatible [3]), VGA/RGB (RGBHV, RGBS, RGsB), component (YPbPr) [4] |
Copy Protection |
HDCP 1.4 |
Maximum Resolutions
Input
Type |
Scan
Type |
Resolution |
Frame
Rate |
Color
Sampling |
Color
Depth |
HDMI |
Progressive |
4096x2160 DCI 4K
&
3840x2160 4K UHD |
24 Hz |
4:4:4 |
30 bit |
30 Hz |
4:4:4 |
24 bit |
30 Hz |
4:2:2 |
36 bit |
60 Hz |
4:2:0 |
24 bit |
2560x1600 WQXGA |
60 Hz |
4:4:4 |
36 bit |
1920x1080 HD 1080p |
60 Hz |
4:4:4 |
36 bit |
Interlaced |
1920x1080 HD 1080i |
30 Hz |
4:4:4 |
36 bit |
VGA/RGB |
Progressive |
1600x1200 UXGA |
60 Hz |
n/a |
1920x1200 WUXGA |
60 Hz |
n/a |
Component |
Progressive |
1920x1080 HD 1080p |
60 Hz |
n/a |
Interlaced |
1920x1080 HD 1080i |
30 Hz |
n/a |
NOTE: Common resolutions are shown; other custom resolutions are supported at pixel clock rates up to 300 MHz for HDMI or 165 MHz for VGA |
Audio |
Input Signal Types |
HDMI (Dual-Mode DisplayPort compatible [3]), analog stereo |
Digital Formats |
Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS®, DTS ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels |
Analog Formats |
Stereo 2-channel |
Analog-To-Digital Conversion |
24-bit 48 kHz |
Analog Performance |
Frequency Response: 20 Hz to 20 kHz ±0.75 dB;
S/N Ratio: >90 dB, 20 Hz to 20 kHz A-weighted;
THD+N: <0.006% @ 1 kHz;
Stereo Separation: >80 dB |
Communications |
HDMI |
HDCP 1.4, EDID, CEC pass-through |
DM Lite Link |
Proprietary link for connection between one DM Lite TX & RX only |
Note: Supports management of HDCP and EDID only when paired with an HD-RX-201-C-E; supports management of CEC between the connected HDMI device and a control system only when paired with an HD-RX-201-C-E |
Connectors |
HDMI IN |
(1) HDMI Type A connector, female;
HDMI digital video/audio input (DVI and Dual-Mode DisplayPort compatible [3]) |
VGA IN |
(1) HD15 connector, female;
RGB (VGA) or component video input [4];
Formats: RGBHV, RGBS, RGsB, YPbPr |
AUDIO IN |
(1) 3.5 mm TRS mini phone jack;
Unbalanced stereo line-level audio input;
Maximum Input Level: 2 Vrms;
Input Impedance: 44k Ohms |
LAN (Front) |
(1) 8-pin RJ45 connector, female;
Passive pass-through to the rear panel LAN jack;
See "LAN Pass-Through (Rear)" specifications below |
SERVICE (Right Side) |
(1) USB Type A connector, female;
For factory use only |
TO RX (Rear) |
(1) 8-pin RJ45 connector, female, shielded;
Link port for connection to a DM Lite receiver [1] |
24VDC 1.25A (Rear) |
(2) Captive screw terminals;
24 Volt DC power input;
Power pack sold separately (if required, model TBA) [2];
Note: This connection powers both the transmitter and receiver; this connection is not normally used when pairing with a surface mount receiver.[2] |
LAN Pass-Through (Rear) |
(1) 8-pin RJ45 connector, female;
Passive pass-through to the front panel LAN jack;
Compatible Cable Standards: CAT5e, CAT6, CAT6a;
Low Level Contact Resistance: 100 mΩ maximum;
Insulation Resistance: 500 mΩ minimum at 500 Volts DC;
Dielectric Withstanding Voltage: 1000 Volts AC between contacts and shell;
Voltage Rating: 125 Volts AC;
Current Rating: 1.5 Amps;
PoE Compatibility: IEEE 802.3at PoE & PoE+;
Insertion Force: 22 N maximum;
Retention Force: 76 N minimum |
Controls & Indicators |
PWR |
(1) Bi-color green/amber LED, indicates operating power is supplied from the RX via the DM Lite link or from a power pack via the 24VDC input, turns amber while booting and green when operating |
HDMI IN |
(1) Bi-color green/amber LED, indicates HDMI input selection and signal presence |
VGA IN |
(1) Bi-color green/amber LED, indicates VGA input selection and signal presence |
INPUT SEL |
(1) Pushbutton for manual input selection, cycles through all available inputs on both the TX and RX |
AUTO |
(1) Pushbutton to enable/disable auto-switching mode, and (1) green LED to indicate auto-switching mode is enabled |
SETUP |
(1) Red LED and (1) recessed pushbutton for Ethernet setup (only when paired with an HD-RX-201-C-E receiver) |
LINK |
(1) Green LED, indicates the DM Lite link status |
RESET |
(1) Pushbutton for hardware reset (Resets both the TX and RX when paired with an HD-RX-201-C-E receiver) |
TO RX (Rear) |
(2) LEDs (on RJ45 connector), green LED indicates link status, amber LED indicates a valid video signal |
Power |
Power Pack (sold separately) |
Input: 100-240 Volts AC, 50/60 Hz;
Output: 1.25 Amps @ 24 Volts DC;
Model: TBA |
Note: This power pack is only required when pairing with a wall plate receiver. When pairing with a surface mount receiver, use the power pack supplied with that receiver. The transmitter and receiver are powered together using a single power pack connected at either the transmitter or receiver (not both).[2] |
Environmental |
Temperature |
32° to 104° F (0° to 40° C) |
Humidity |
20% to 90% RH (non-condensing) |
Construction |
Composition |
Metal housing and bracket with black or white polycarbonate front label overlays |
Mounting |
Mounts in a 2-gang, 2-1/4 inch (57 mm) deep U.S. electrical box or plaster ring (not included) |
Faceplate |
Requires a Crestron FP-G2-DM-B-T or FP-G2-DM-W-T faceplate (sold separately, other faceplates are incompatible) |
Dimensions |
Height |
4.19 in (107 mm) |
Width |
3.50 in (89 mm) |
Depth |
2.07 in (53 mm) |
Weight |
8.9 oz (252 g) |
Compliance |
UL Listed for US & Canada, CE, IC, FCC Part 15 Class B digital device |
Maximum DM Lite Link Cable Lengths |
Resolution |
Cable Type |
CAT5e (or better),
DM-CBL-ULTRA DM® Ultra Cable, or
DM-CBL-8G DM 8G DM 8G® Cable [1] |
1920x1080 FHD 1080p |
230 ft (70 m) |
1920x1200 WUXGA |
1600x1200 UXGA |
2048x1080 DCI 2K |
2048x1152 QWXGA |
2560x1080 UWFHD |
130 ft (40 m) |
2560x1440 WQHD |
2560x1600 WQXGA |
3840x2160 4K UHD |
4096x2160 DCI 4K |
|