DALI® Interface, DIN Rail Mount
The DIN-DLI is a DALI-2™ certified DALI® interface for Crestron control systems that provides control of one DALI loop.
The DIN-DLI is a DALI-2™ certified DALI® interface for Crestron control systems that provides control of one DALI loop. Housed in a 3M DIN-rail enclosure, the compact DIN-DLI is capable of controlling DT0, DT1, DT2, DT3, DT4, DT5, DT6, DT7, and DT8 (Tc)2 DALI devices. Crestron control system connection is provided through a Cresnet® wired or Ethernet with PoE connection. DALI devices can be commissioned through an intuitive web user interface. The DIN-DLI also offers unique features that improve the flexibility and performance of DALI® systems in ways that will help you to be successful with your DALI installation
One DALI Loop
The single DALI loop on the DIN‑DLI enables control of up to 64 individual DALI devices. With DALI's device level control, lighting loads powered from the same feed can be controlled individually. DALI allows layout changes without new circuit wiring, providing flexibility by allowing zone reconfiguration after a system is installed.
Integrated DALI Power Supply
The design of the DIN‑DLI eliminates the need for external power supplies required by other DALI controllers on the market. Power1 is delivered via PoE or Cresnet, creating a true single-wire installation. Both Cresnet and PoE are capable of powering the communications of all 64 DALI ballast controllers.
Override Input
Override input is provided to allow an external contact closure to momentarily override the control system program and set each channel output to its override preset level. Factory default override values on DALI devices can be adjusted through the DIN-DLI web user interface.
DIN Rail Installation
The 3M 2.08 in. (52.83 mm) wide DIN‑DLI snaps onto a standard DIN rail for installation in a wall mount enclosure. When installed in an enclosure utilizing 45 mm cutouts, the front panel stays accessible while the connections are concealed.
Module to Module Connectors
Module to Module connectors quickly connect Cresnet and Override between modules without the need for additional wiring or tools.
Cresnet® and PoE
The DIN‑DLI communicates with Crestron control systems via the Cresnet control network or Power-over-Ethernet (PoE). A pair of Cresnet ports and module to module connectors allow for easy daisy-chaining of several DIN Rail Series automation control modules. An RJ45 connector enables both data and power to be transmitted to the unit using a single CAT5 or higher cable.
NOTE: The DIN‑DLI is not compatible with Crestron 2‑Series control systems or earlier.
Key Features
- Interfaces with one independent DALI® loop
- DALI-2™ certified
- Supports DT0, DT1, DT2, DT3, DT4, DT5, DT6, DT7, and DT8 (Tc)2 DALI Devices
- Controls up to 64 DALI devices
- Ethernet or Cresnet® wired communication
- Power using Cresnet network or PoE for single-wire installation
- Provides loop power for communication
- Commissioned through Web UI or Crestron Home® OS for easy setup
- Override input
- 3M wide DIN rail mounting
- Internal diagnostics
- Works with the Crestron Home® OS
| Power |
| Cresnet Power Usage |
6W (250mA @ 24V) |
| PoE Power Usage |
IEEE 802.3af (802.3at Type 1) Class 2 PoE
Powered Device (6.5W) |
| Load Ratings |
| DALI Loop |
1 |
| DALI Devices |
64 |
| Load Types |
DALI devices DT0, DT1, DT2, DT3, DT4, DT5, DT6, DT7, and DT8 (Tc)2 |
| DALI Bus |
Maximum: 0.25A |
| Power Supply1 |
Guaranteed: 0.17A |
| Communications |
| Cresnet |
Cresnet secondary mode |
| Ethernet |
100BASE-TX
IEEE 802.3af (802.3at Type 1) Class 2 PoE Powered Device (6.5W)
MbedTLS encryption
Authentication prompted on first connection |
| DALI |
DALI bus, one DALI loop;
DALI-2™ Certified;
Provides power and communication for the DALI bus;
Up 64 DALI drivers in up to 16 DALI groups;
DT0, DT1, DT2, DT3, DT4, DT5, DT6, DT7 and DT8 (Tc)2 support |
| Connectors |
| Module to Module |
(2) Module to module connectors;
Provides Cresnet and Override to connected modules |
| NET |
(2) 4-pin 3.5 mm detachable terminal blocks, paralleled;
Cresnet secondary port |
| OVERRIDE |
(2) 2-pin 3.5 mm detachable terminal blocks, paralleled;
Sensing input for external low-voltage contact closure;
Activates override mode when a closure is present;
Minimum Closure Rating: 10mA (per module) at 24V |
| LAN PoE |
(1) 8-pin RJ-45, female;
100BASE-TX Ethernet port;
Green and yellow LEDs indicate Ethernet port status;
Cresnet network power disables PoE power |
| DA+ / DA- |
(2) 2-pin 3.5 mm spring terminals, paralleled;
Control a single DALI loop;
A DALI loop controls up to 64 drivers;
3kVAC isolation between Cresnet (NET) Ethernet (LAN PoE) ports;
Wire Gauge: 12-24 AWG solid wire or 14-24
AWG stranded wire |
| Controls and Indicators |
| OVR |
(1) Red LED and (1) push button;
For enabling override mode and saving override presets |
| PWR |
(1) Green LED;
Indicates power to device |
| NET |
(1) Yellow LED;
Indicates communication with the control processor |
| RESET |
(1) Recessed miniature push button;
Resets internal processor
Factory restore |
| DALI |
(1) Yellow LED;
LED lights to indicate DALI power, communication, and error |
| TEST |
(1) Push button;
Provides local control of the lights;
Used to initiate a single device replacement |
| Environmental |
| Local In-cabinet Air Temperature |
32° to 122 °F (0° to 50°C) |
| Humidity |
10% to 90% RH (noncondensing) |
| Heat Dissipation |
13.6 BTU/hr |
| Construction |
| Enclosure |
Light gray polycarbonate housing with polycarbonate label overlay |
| Mounting |
35 mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45 mm front panel cutout, occupies 3 DIN module spaces (54 mm) |
| Dimensions |
| Height |
3.68 in. (93.70 mm) |
| Width |
2.08 in. (52.83 mm) |
| Depth |
2.32 in. (59 mm) |
| Weight |
| 0.24 lb (113.3 g) |
| Compliance |
Regulatory Model: M202236001
Intertek® Recognized for US & Canada, CE, FCC Class B, IC, WEEE |
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.