Master Photo: DM-EXT-2011 KIT
Add to Favorites

DM-EXT-2011 KIT

4K60 4:4:4 DM® Essentials Transmitter Receiver Pair for USB‑C® DisplayPort™, USB 2.0, and Ethernet Signal Extension over CATx Cable

Provides a cost-effective, high-definition AV presentation solution for classrooms and meeting spaces. Consists of a transmitter (HD‑TXU‑4KZ‑111‑E) and receiver (HD‑RXU‑4KZ‑101‑E) that enable point-to-point signal extension over HDMI® video, USB 2.0, and Ethernet signals over a CATx cable. 4K scaling HDMI output ensures a reliable, high-quality video image. Supports 4K60 4:4:4, HDR10, HDR10+, and Dolby Vision® video.

Have a question?
Add to a Project
Find a Dealer

The DM‑EXT‑2011 KIT consists of a transmitter (HD‑TXU‑4KZ‑111‑E) and receiver (HD‑RXU‑4KZ‑101‑E), and enables the extension of HDMI® and USB 2.0 signals. This is useful in applications where an AV source is located remotely from its destination, such as a display, projector, or codec solution. A CAT5e or higher twisted pair cable must be used to connect the transmitter and receiver.1

NOTE: Power is transmitted over the CATx cable that connects the transmitter to the receiver.

4K60 4:4:4 and HDR Support
The DM‑EXT‑2011‑KIT supports video resolutions up to 4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby Vision® video formats are also supported.2

USB 2.0 Data Extension
Two USB 2.0 host ports are provided on both the HD‑TXU‑4KZ‑111‑E and HD‑RXU‑4KZ‑101‑E, enabling connection to a wide variety of supported USB 2.0 peripheral devices.4

Ethernet Pass-Through Capability
The transmitter and receiver are each equipped with a 100/1000 Mbps LAN port that passes an Ethernet signal over the DM connection. The LAN port of one endpoint in the pair can be connected to an Ethernet network while the LAN port of the other endpoint can be connected directly to an Ethernet-enabled device such as a PC.

Low Profile Installation
The transmitter and receiver can be placed on or attached to a flat surface. The transmitter can fit discreetly inside a presentation lectern or be attached to the underside of a table. The receiver can be mounted onto a wall behind a display or onto a ceiling above a projector. The devices are also rack rail mountable.

 
Key Features
  • 4K60 video with 4:4:4 color sampling
  • Transmitter and receiver for extension of a USB-C® DisplayPort™ AV signal, USB 2.0 data signals, and Ethernet signal over a CAT5e or higher cable
  • 2x1 auto-switching transmitter and 2x1 auto-switching receiver for extension of a USB-C® DisplayPort™ AV signal or HDMI® signal and USB 2.0 data over a CAT5e or higher cable
  •  HDR10, HDR10+, and Dolby Vision® video formats
  • Signal extension distance up to 130 ft (40 m) for UHD and 4K signals or up to 230 ft (70 m) for 1080p, WUXGA, and 2K signals
  • EDID and HDCP 2.3 management
  • Consumer Electronics Control (CEC) capability
  • Ethernet, EDID, and CEC pass-through capability
  • Low-profile installation
  • 100-240VAC power pack included

Notes:

  1. For the DM CATx cable connection, use Crestron DM-CBL-8G, Crestron DM‑CBL‑ULTRA, or third-party CAT5e or higher cable. To safeguard against unpredictable environmental electrical noise that may impact performance at resolutions above 1080p, shielded cable and connectors are recommended for all applications and are required when bundling multiple cables in a wire run. Wire and cables are sold separately.
  2. 4K60 4:4:4 performance and HDR support require the use of USB-3.2 Gen 1 (5 Gbps) cables with support for DisplayPort Alt Mode (DisplayPort 1.4 video, 4K60 4:4:4, 2 lanes). Cables are sold separately.
  3. 4K60 4:4:4 performance and HDR support require the use of HDMI cables and couplers with a minimum TMDS bandwidth of 18 Gbps. If 4K60 4:2:0 or 4K30 4:4:4 performance is acceptable, cables and couplers with a minimum bandwidth of 10.2 Gbps may be used. Bandwidth loss is cumulative; therefore, performance may be reduced when inserting multiple cables and couplers inline.
  4. The HD‑TXU‑4KZ‑111‑E and HD‑RXU‑4KZ‑101‑E are engineered to deliver maximum compatibility with the widest possible range of USB devices. Crestron does not guarantee that all USB devices are compatible with the HD‑TXU‑4KZ‑111‑E and HD‑RXU‑4KZ‑101‑E.
  5. The HDMI output requires an appropriate adapter or interface cable to accommodate a DVI signal. CBL‑HD‑DVI interface cables are sold separately.

This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

The specific patents that cover Crestron products are listed online at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, .AV Framework, 3‑Series, AirMedia, Auto-Locking, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, QuickSwitch HD, and XiO Cloud are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, Dolby Digital, and Dolby Vision are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries. HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Intertek and the Intertek logo are either trademarks or registered trademarks of Intertek Group in the United States and/or other countries. USB Type-C and USB‑C are either trademarks or registered trademarks of USB Implementers Forum, Inc. in the United States and/or other countries. DisplayPort is either a trademark or registered trademark of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2024 Crestron Electronics, Inc.

 
Video
Input Signal Types DisplayPort™ over USB-C® (DisplayPort Alt Mode) with HDR10, HDR10+, Dolby Vision®, Deep Color, and 4K60 4:4:4 support2
Output Signal Types HDMI® with HDR10, HDR10+, Dolby Vision, Deep Color, and 4K60 4:4:4 support2
Copy Protection HDCP 2.3
Maximum Resolutions Common resolutions are listed in the following table.
Scan Type Resolution Frame Rate Color Sampling Color Depth
Progressive 4096x2160 DCI 4K & 3840x2160 4K UHD 24 Hz 4:4:4 12 bit
30 Hz 4:4:4 12 bit
60 Hz 4:2:2 12 bit
60 Hz 4:4:4 8 bit
2560x1600 WQXGA 60 Hz 4:4:4 8 bit
1920x1080 HD
1080p		 60 Hz 4:4:4 12 bit
NOTES:
  • The maximum supported resolution is 4K60 with 4:4:4 color sampling. Custom resolutions are supported at pixel clock rates up to 600 MHz.
  • Interlaced video sources are not supported.
Audio
Input Signal Type DisplayPort over USB-C (DisplayPort Alt Mode)
Output Signal Type HDMI
Digital Formats Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby® TrueHD, Dolby Atmos®, DTS®, DTS ES, DTS 96/24, DTS HD® High Res, DTS-HD Master Audio, DTS:X®, LPCM up to 8 channels
Communications
Ethernet 100/1000 Mbps pass-through
HDMI HDCP 2.3, EDID, CEC pass-through
DM HDCP 2.3, EDID;
USB 2.0 up to 300 Mbps
USB USB signal extension via USB 2.0 host ports
Connectors - Transmitter (HD‑TXU‑4KZ‑111‑E)
24 VDC 1.4A (1) 2.1 x 5.5 mm DC power connector;
24VDC power input;
PW-2420RU power pack included

NOTE: Either included power pack will power both the transmitter and the connected receiver. Do not connect both power packs at once.
DM (1) 8-pin RJ-45 connector, female, shielded;
DM output port for connection to the receiver1
USB INPUT (1) USB Type‑C® connector, female;
Digital video/audio input using DisplayPort Alt Mode;
USB 2.0 data support
LAN (1) 8-pin RJ‑45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
Passes Ethernet signal over the DM connection to the receiver
HOST (2) USB Type-A connectors, female;
USB 2.0 host ports;
USB signal extender ports for connection to USB mice, keyboards, or other USB 2.0 peripheral devices;4
Available Power: 500mA @ 5VDC per port
SERVICE (1) USB 2.0 Type-A connector, female;
Used for firmware loading, configuration management, or as a USB host port for one TT‑100 series cable caddy (sold separately);
Can also provide up to 5V, 500mA power to a USB powered device
Ground (1) Chassis ground lug
Connectors - Receiver (HD‑RXU‑4KZ‑101‑E)
DM IN (1) 8‑pin RJ‑45 yellow connector, female, shielded;
DM input port for connection to the transmitter1
HDMI OUTPUT (1) HDMI Type A connector, female;
HDMI digital video/audio output (DVI compatible4)
LAN (1) 8-pin RJ‑45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
Receives Ethernet signal from the transmitter over the DM connection
24 VDC 1.4A (1) 2.1 x 5.5 mm DC power connector;
24VDC power input;
PW-2420RU power pack included

NOTE: Either included power pack will power both the receiver and the connected transmitter. Do not connect both power packs at once.
SERVICE (1) USB 2.0 Type‑A connector, female;
Used for firmware loading, configuration management, or as a USB host port for one TT-100 series cable caddy (sold separately);
Can also provide up to 5V 500 mA power to a USB powered device
HOST (2) USB Type-A connectors, female;
USB 2.0 host ports;
USB signal extender ports for connection to USB mice, keyboards, or other USB 2.0 peripheral devices;4
Available Power: 500mA @ 5VDC per port
Ground (1) Chassis ground lug
Controls and Indicators - Transmitter (HD‑TXU‑4KZ‑111‑E)
PWR (1) Green/amber bi-color LED;
Amber indicates that the device is booting;
Green indicates that the device is operational
INPUT (1) Green LED, indicates that the device is receiving a DisplayPort over USB‑C (DisplayPort Alt Mode) input signal
DM OUT (2) LEDs on RJ‑45 connector, one green and one amber;
Green indicates that DM link is established;
Flashing amber indicates non‑HDCP video;
Solid amber indicates HDCP video
LAN (2) LEDs on RJ-45 connector, one green and one amber;
Green indicates that a 100 Mbps link is established;
Solid amber indicates that a 1000 Mbps link is established;
Flashing amber indicates 1000 Mbps Ethernet activity
Controls and Indicators - Receiver (HD‑RXU‑4KZ‑101‑E)
PWR (1) Green/amber bi-color LED;
Amber indicates that the device is booting;
Green indicates that the device is operational
DM IN (2) LEDs on RJ-45 connector, one green and one amber;
Green indicates that DM link is established;
Flashing amber indicates non-HDCP video;
Solid amber indicates HDCP video
LAN (2) LEDs on RJ-45 connector, one green and one amber;
Green indicates that a 100 Mbps link is established;
Solid amber indicates that a 1000 Mbps link is established;
Flashing amber indicates 1000 Mbps Ethernet activity
Power
Power Pack (included with Transmitter and Receiver) Input: 100-240VAC;
Output: 24VDC 2.5A;
Models: PW‑2420RU

NOTE: Either included power pack will power both the transmitter and receiver. Do not connect both power packs at once.
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% RH (non-condensing)
Construction
Chassis Metal, black finish, vented sides, 2 mounting flanges
Mounting Surface or rack rail mount
Dimensions - Transmitter (HD‑TXU‑4KZ‑111‑E)
Height 1.20 in. (30 mm)
Width 4.19 in. (106 mm)
Depth 7.94 in. (202 mm)
Dimensions - Receiver (HD‑RXU‑4KZ‑101‑E)
Height 5.11 in. (130 mm)
Width 4.19 in. (106 mm) with mounting flanges attached
Depth 7.94 in. (202 mm)
Weight
Transmitter 1.2 lb (0.55 kg)
Receiver 1.19 lb (0.54 kg)
Compliance
Regulatory Model: M202047005
Intertek® Listed for US and Canada, CE, IC, FCC Part 15 Class B digital device
Click here to search product certificates.

Notes:

  1. For the DM CATx cable connection, use Crestron DM-CBL-8G, Crestron DM‑CBL‑ULTRA, or third-party CAT5e or higher cable. To safeguard against unpredictable environmental electrical noise that may impact performance at resolutions above 1080p, shielded cable and connectors are recommended for all applications and are required when bundling multiple cables in a wire run. Wire and cables are sold separately.
  2. 4K60 4:4:4 performance and HDR support require the use of USB-3.2 Gen 1 (5 Gbps) cables with support for DisplayPort Alt Mode (DisplayPort 1.4 video, 4K60 4:4:4, 2 lanes). Cables are sold separately.
  3. 4K60 4:4:4 performance and HDR support require the use of HDMI cables and couplers with a minimum TMDS bandwidth of 18 Gbps. If 4K60 4:2:0 or 4K30 4:4:4 performance is acceptable, cables and couplers with a minimum bandwidth of 10.2 Gbps may be used. Bandwidth loss is cumulative; therefore, performance may be reduced when inserting multiple cables and couplers inline.
  4. The HD‑TXU‑4KZ‑111‑E and HD‑RXU‑4KZ‑101‑E are engineered to deliver maximum compatibility with the widest possible range of USB devices. Crestron does not guarantee that all USB devices are compatible with the HD‑TXU‑4KZ‑111‑E and HD‑RXU‑4KZ‑101‑E.
  5. The HDMI output requires an appropriate adapter or interface cable to accommodate a DVI signal. CBL‑HD‑DVI interface cables are sold separately.

This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

The specific patents that cover Crestron products are listed online at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, .AV Framework, 3‑Series, AirMedia, Auto-Locking, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, QuickSwitch HD, and XiO Cloud are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, Dolby Digital, and Dolby Vision are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries. HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Intertek and the Intertek logo are either trademarks or registered trademarks of Intertek Group in the United States and/or other countries. USB Type-C and USB‑C are either trademarks or registered trademarks of USB Implementers Forum, Inc. in the United States and/or other countries. DisplayPort is either a trademark or registered trademark of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2024 Crestron Electronics, Inc.

Pricing Region Select
Please select your region below to see the appropriate Advertised Pricing.