Crestron

Crestron Toolbox

Crestron Toolbox Release Notes

Introduction

Thank you for installing the Crestron Toolbox. The following sections are available in the release notes:

System Requirements

Supported Operating Systems
Minimum required PC configuration
Recommended PC configuration

Changes Since Last Version

These are changes that have been made since the last numerical version unless a different version has been noted. Note that the version is consistent accross all Toolbox tools and thus all are listed here. While there may not be any explicit Tool changes, Core Toolbox changes may affect device specific support and general stability.

Toolbox 2.42.240 (07-06-2016)

Known Issues

The following are items which may differ than what might be expected but are by design and are not planned to change.
  • Serial HW Handshaking (RTS/CTS) is stricter than the Viewport was. If a device has RTS/CTS on and Toolbox does not, you will not be able to communicate.
The following issues are known and will be addressed in future versions.
  • From the Easy Config Tool only, and only if the address book says “ctp” as the connection method, and only if the user has enabled SSL on the device that it is trying to connect to, then the connection from the Discovery Tool will fail.
    • The workaround: Change the address book connection string to “AUTO” or “SSL”.
  • NEW Toolbox does not support concurrent use by multiple users on a PC. In otherwords, you cannot run Toolbox under one user then use the Windows switch user function and run Toolbox under the other user as well.
  • A computer going into Sleep or Hibernate mode may cause a running instance of Toolbox to enter the "Switch-To-Retry" state. While we are actively looking for a resolution to this problem, knowing this is a trigger may help avoid this situation.
  • When naming addresses in the address book, do not start those names with "tcp", "ssl", "usb" or "rs232" as these while they will work for direct connections will not work properly if used in indirect connections.
  • X Generation Processors do NOT support Touch Settable ID operations. Therefore when there are conflicting TSIDs on a cresnet network on an X Generation System, The Network Tree will show these conflicts and not allow any operations on those devices. In addition there is no way to resolve the conflict on the X Generation Processor. A work around is to address the device specifically in the address book and connect to it using the System Info Tool. Using this tool you will be able to perform all the same operations you would have through the Network Device Tree.
  • Transfer dialogs restrict transfers to one at a time. Use a script or multiple instances of Toolbox for simultaneous transfers.
  • Some error messages leave much to be desired.
  • USB driver is Unsigned and thus may cause Windows to attempt to find a better one online or show warnings upon installation.
  • While using the QM Audio Config Tool, if you have a text cosnole open to the same device over cresnet, some operations and updates may be slower than usual. To correct this, close all text consoles while using the QM Audio Config Tools.
  • Regarding the "Allow 16-level fonts to load" check box on the Touch Panel Project Dialog. VTPro uses this standard project dialog so the setting WILL be in effect. The only stipulation is that VTPro can be set to auto-load the project in which case the dialog does not give the user a chance to change settings and just starts loading immediately. In this case it may be missed, or they will have to turn off the auto-send to have a chance to change the setting. The setting will be persistent in this case. So if they uncheck then turn auto-send back on, it will continue to send only the 4-level fonts. Loads through System Builder and D3Pro do NOT use this standard dialog and therefore will always attempt to load 16-level fonts if the panel supports them, regardless of the state of this check box. To specify this setting in scripting see the command ability_functions_DisplayListSetSpecialLoadBehavior. Also note that some models of touch panels have a command to disable 16-level font support wchich if done, will override any Toolbox setting and prevent the 16-level fonts from loading. See the release notes of the latest FW for your Touch Panel for details.
  • Regarding DM Tool for DigitalMedia. While the DM Tool is running, if the connected device (DM Switcher) experiences a reboot for ANY reason The DM Tool will no longer show correct status updates. In this case you should close all Toolbox tools and Apps (including SIMPL Windows, System Builder, VTPro-E) and then relaunch the DM Tool.
  • All Tools: if multiple instances of a tool are opened, then one is closed, all other open instances will not work correctly. If this occurs, close down all open tool instances, then open a new tool instance to have full functionality restored.
  • Under certain network conditions involving Ethernet devices without control system connections, the InifiNetEX diagnostics tool may not show InfinetEX devices or any appear to hang. To work around this until it is fixed, connect directly to the InfiNetEX gateway. This may be an Ethernet address for external gateways or it may be an indirect slot address for built in gateways on the 3-Series processors.
The following issues involving Toolbox have work arounds or posted fixes, and therefore will not be fixed.
  • The SMW Program Tree may not show proper menu items for certain devices which cannot be programmed in SIMPL windows. This includes but is not limited to the AES. A fix for this issue has been included in SIMPL Windows 2.07.21.
The following issues involve interactions between Toolbox and some third party applications which may be installed on a computer. There are no plans on resolving these issues beyond updating or uninstalling the noted application.

Toolbox currently does not support the following.

Toolbox Change Log History

Toolbox 2.41.616 (06-09-2016)
Toolbox 2.41.513 (05-02-2016)
Toolbox 2.41.418 (4/4/2016)
Toolbox 2.41.315 (2/24/2016)
Toolbox 2.41.252 (2/2/2016)
Toolbox 2.41.224 (1/19/2016)
Toolbox 2.40.863 (12/7/2015)
  • Core Toolbox
    • Added support for DM-TX-4K-202-C/302-C
    • Improved support for DIN-CENCN2
    • Corrected an issue where Device Discovery would sometimes report 0 discovered devices
    • Device Discovery- The DM-RMC-100-STR now redirects to the web page from the device
    • Addressed a lockup that could occur during a CEN-CI3 PUF update
    • Addressed firmware downgrade issue with MP-B10/20 devices
    • Protects against potential COM Server crash when a DGE-100 is in the system
  • DM Tool
    • Improved stability of DM Tool
    • Corrected issue with DMC-STR/STRO remaining on the Initializing dialog when opening the device
    • Added editable EDID for many DM Room Boxes
      • RMC-4K-SCALER-C, RMC-4K-SCALER-C-DSP, DM-RMC-200-C, DM-RMC-SCALER-C, DM-RMC-200-S, DM-RMC-200-S2, DM-RMC-SCALER-S, and DM-RMC-SCALER-S2
  • DMPS Tool
    • Corrected issue with many of the help buttons not functioning
  • SIMPL Debugger
    • Fixed "Send only specified signals" feature
    • Corrected error when loading the sig file
  • EDID Tool
    • Protects against a potential crash when opening EDID File (when UAC is enabled)
  • Sonnex Tool
    • Correct issue related to Configuration File transfers failing to send to expanders
  • System Monitor
    • Corrected startup issue where System Monitor could hang while on the "requesting settings" dialog
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.40.731 (11/3/2015)
  • Core Toolbox
    • Added support for DIN-CENCN2
    • Corrected issue when updating HD-XSPA Puf files.
  • DM Tool
    • Support HDCP 2.2 on future HDCP 2.2 cards.
    • UI updates for supporting high resolution monitors and large font size.
    • DMC-STR: Display Streaming Status and Decoder Status.
    • DMC-STR: Corrected Network Ready indicator.
    • DMC-STRO: Can now adjust stream ports.
    • DM-RMC-4K-SCALER-C: 24hz Resolutions are now present in DMTool.
    • DMC-4K-HDO UI changes to be consistent with other scaler products.
  • DMPS Tool
    • No Tool Changes
  • EDID Tool
    • No Tool Changes
  • SIMPL Debugger
    • Improved performance when finding a signal
    • Added the ability to copy the signal name to the clipboard
    • Added a button to pause scrolling
  • Sonnex Tool
    • No Tool Changes
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.40.617 (08/12/2015)
  • Core Toolbox
    • Windows 10 support tested and confirmed
    • DMC-STR firmware update fixes and optimizations
    • Added support so that concurrent connections by hostname and IP utilize the same socket to avoid issues with devices that only support a single console socket
    • Exposed RAVA config dialog for supported TSX-xx0 panels (TST-600, TSW-750, etc..)
    • Fixed issues with the COM server staying loaded after closing Toolbox, sometimes after a failed PUF load
    • Hostname warning appears when user visits Ethernet config dialog without making changes
    • Corrected URL used to connect to the DMPS3-4K-150-C from EasyConfig to match new FW
    • Added install warning that Toolbox no longer supports Windows XP and Server 2003 R2
    • Fixed potential crashes using System Info Tool and SIMPL Debugger
    • Fixed an issue causing DM Tool to fail to show any installed cards
    • PUF tool can now use detected indirect address during analysis step, fixes some version detection in DM systems
    • Moved initial PUF file loading to it's own thread to keep the application responsive for large files
    • Fixed problem connecting to USB with existing open Ethernet connections
  • DM Tool
    • DM-4K-HDO-SCALER - Added scaler support
    • If an EDID is rejected by firmware, the tool should present a message box to the user.
    • DM Test Report format updates and addition of PNM System ID
    • Toolbox Crashed when Opening DM Tool and Text Console to 32x32 with DMC-STRs Streaming
    • EDID selection from outputs not including all outputs on DM-MD6X1
    • DM-TX-401-C doesn't show connected USB devices properly
    • DM-RMC-4K-100-C does not display correct information
    • DMC-C(-DSP) & DMC-4K-C(-DSP) - Add HDCP Support check box
    • DMC-STR - Switching initiations in DM Tool does not switch the Initiations on the device immediately
    • DMC-STR - Add Network Ready status to DM tool
    • DMC-STR - When streaming, incoming arrow to card always displays no connection regardless of state
    • DMC-STR - Stream Location text in "By Receiver" should be non-editable, but selectable
    • DMC-STR/STRO - Display streaming status on top of arrow and resolution/bitrate underneath arrow
    • DMC-STRO multi-cast address is not displayed after the stream is started
  • DMPS Tool
    • DM Test Report format updates and addition of PNM System ID
    • DMPS3 - the minimum and maximum settings switched for ease of use in each output
    • Fixed help file link for DMPS3-300-C-AEC
    • Provide help file description for Mixer Enabled/Bypassed mode for DMPS3 inputs
  • EDID Tool
    • Resolution "640x480" needs to be included in all default EDIDs
    • Do not replace "." with "_" when saving EDID files
    • Fixed "Get EDID From" & "Save EDID ..." location not being remembered
    • VESA block modify dialog - maximum list has wrong foreground color, difficult to read text
  • Sonnex Tool
    • Allow the 2 SPDIF outputs on the main SWAMP to be named on compatible firmware
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.40.325 (7/7/2015)
  • Core Toolbox
    • Made a number of dialogs re-sizable
    • Added support for resolving hostnames to use the same socket as an existing connection. Resolves connection issues with some devices with limited resources like DM Endpoints
    • Fixed Discovery via Fusion for control system models with a '-' in the model name
    • Fixed crash in Help->About reported on some systems
    • Added RAVA configuration support in System Info for supported Android (TSx-XXX2) devices
    • Remove incorrect IP Table support for TST-902, TST-602, and TSR-302
    • Fixed erroneous hostname warnings on Ethernet dialog
    • Fixed Discovery Tool to show proper icons for some devices
    • Fixed crash often seen when re-loading SIG files after re-compiling and returning to the debugger
  • DM Tool
    • Fixed crash when customizing HDMI Extensions
    • Fixed a number of crashes in DM Tool which could leave the COM Server running
    • Fixed HDCP indication on input side of DMC-4K-HD
    • Added adjustable time delay to downmixed audio
    • Added support for Video Wall & Bezel compensation configuration
    • Added support for 4K 60Hz
  • DMPS Tool
    • Added HDCP Support On/Off for DM Input
  • EDID Tool
    • Added support for 4K 60Hz
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.40.219 (5/28/2015)
  • Core Toolbox
    • Added user interface in System Info for configuring RAVA on DMPS3-300-C-AEC
    • Added support for authentication banners over SSH when sent by supported devices
    • Resolved a problem loading a config file to a DMPS that includes a program
    • Added bootloader support to C2N-AMP-6X100
    • Corrected some issues causing failures loading FW to MP-Bxx devices
    • Fixed some timing issues related to sending projects to TPMC-4SM devices
    • PUF Tool - Closed a loophole where a new OOTBF would not be loaded to DMPS devices in some cases
    • PUF Tool - Fixed UI to show time remaining for file transfers
    • Script Tool - After changing a script using an external editor, reload query could not be dismissed
    • SystemInfo Tool - Added Primary DNS server info to "Save File" option
    • Set Cresnet and Error Log panes to always be collapsed by default to speed up initial tool loading. Will load on demand when and if expanded
    • Made changes to mitigate privilege elevation issues between Toolbox, SIMPL, Studio, and VTPro. Fixes crash of Toolbox if it is launched after one of the other apps has used Toolbox
  • DM Tool
    • Fixed an issue that could cause the VptComServer process to remain running when not needed.
    • Fixed issues related to showing real-time updates on highly populated 32x32 switchers
    • Corrected Help File Links for DMC-STR/DMC-STRO UIs
    • Added support for Audio Time-Delay on the following models with updated firmware:
      • DMC-HD-DSP, DMC-4K-HD-DSP, DMC-C-DSP, DMC-4K-C-DSP, DMC-S-DSP, DMC-S2-DSP, DM-RMC-4K-SCALER-C-DSP
  • DMPS Tool
    • Added support for DMPS3-300-C-AEC
    • Corrected some help file links
    • Fixed some startup performance issues
  • EDID Tool
    • Added scroll bar to EDID pop-up details window
    • Fixed several issues with the filename generation
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.38.880 (4/30/2015)
  • Core Toolbox
    • Fixed ability to load DIP IP Table file formats to devices
    • Fixed crash seen after waking a computer from sleep with Toolbox open
    • Fixed DNS Server configuration for DM endpoints
    • Fixed issue that would leave a control system program stopped after loading through Studio
    • Fixed issues in the COM server which were causing crashes and hangs when operations were being canceled
    • Fixed issues running Toolbox after starting SIMPL, VTPro or Studio
    • Fixed Roaming configuration support for TSX Touch Panels
    • Fixed Switch-To-Retry in Network Setup Wizard when using "Manual Setup" in Studio
    • Fixes for setting RF IDs on some devices
    • Licensing dialog fixes to recognize additional features and added a Close button
    • Optimized load time of device data on new connections
    • Removed some items in the network tree for DM that were used only for internal purposes
  • DM Tool
    • Added URL to launch the tool for the DM-MD8X1-4K-C and HD-MD8X1-4K
  • DMPS Tool
    • Corrected some text and setting ranges
    • Fixed a bug that could cause DMPS tool to crash or hang if there is a loss of communications while loading
    • Fixed crash that could occur when loading Toolbox with multiple DM/DMPS tools open
    • Added URL to launch the tool for the DM-MD8X1-4K-C and HD-MD8X1-4K
  • EDID Tool
    • No Tool changes
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • HDXSP - Fixed Device Configuration Saving and Loading
Toolbox 2.38.823 (3/11/2015)
  • Core Toolbox
    • New support for the following devices
      • DMC-4K-HDO(-DSP)
      • DM-RMC-4K-100-C-1G and DM-TX-4K-100-C-1G
    • Improve display project loading reliability and performance.
    • Include missing device images for Device discovery
    • Increased reboot timeout for DM and 3-Series devices.
    • Fixed baud rate detection for iLux Designer.
  • DM Tool
    • Support for the new products in this release
    • Remove old EDID template files when installing new toolbox. This fixes a potential crash after upgrading from earlier versions.
    • DMC-STRO
      • Fixed an issue where the tool would be greyed out after connecting
  • DMPS Tool
    • No Tool changes
  • EDID Tool
    • No Tool changes
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.38.747 (2/2/2015)
  • Core Toolbox
    • New support for the following devices
      • DMC-4K-C(-DSP)
      • DM-RMC-4K-SCALER-C
      • DM-RX1-4K-C-1G and DM-TX1-4K-C-1G
      • DMC-STR
    • Improved SFTP speed and added better error messages and handling for SSH
    • Display Project Window would show an error when connecting over SSH
    • Fixed an issue when the IP Table entry description field contained a ">"
    • Corrected some timeouts for Touch Screen project loads
    • Fixed the program information dialog in System Info for SIMPL# programs
    • Network Setup Wizard
      • Fixed error message "Unable to find custom...."
      • Fixed a freeze when connecting to a system with duplicate IDs
      • Fixed an issues causing the discovered lists to sometime be incomplete
      • Updated Help file with additional setup information
  • DM Tool
    • Support for the new products in this release
    • HDBase-T support
    • System Wide new EDID configuration scheme and test report
    • Fixed .NET error when refreshing Ethernet settings on the DM-RMC-100
    • Fixed some template EDID files for audio
    • DMC-STRO
      • Add Audio control
      • Fixed port settings dialog
      • Fixed Mute issue
      • Fixed an issue where the tool would be greyed out after connecting
  • DMPS Tool
    • Test report for new EDID scheme
    • Fixed a crash if the connected device rebooted while connected
    • Added support for HDBase-T device recognition
    • Fixed an issue causing the tool to prompt for a password when there was none on the DMPS
  • EDID Tool
    • No Tool changes
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.38.637 (11-13-2014)
  • Core Toolbox
    • New support for DMPS3-4K-150-C
  • DM Tool
    • Support URL link to DMPS3-4K-150-C
  • DMPS Tool
    • Support URL link to DMPS3-4K-150-C
  • EDID Tool
    • No Tool changes
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.38.617 (10-28-2014)
  • Core Toolbox
    • New Features
      • SSH/SFTP support - Improved SFTP file transfer performance.
      • TPMC-V12 & TPMC-V15 Patch support
    • New device support
      • DMPS3-200-C and DMPS3-300-C Support
      • DMC-STR support and new DMC-STRO support.
      • HR-100 and HR-150
      • CLFI-LDIMUEX
      • C2N-AMP-6X100
    • Bugs Fixed
      • When using SFTP, Toolbox may send more files than necessary with "Send only modified" checked
      • When setting static IPs on DM with PNM disabled, conflicting IP ranges were reported.
      • Loading projects to TPCS-4SMD would result in a file mismatch warning.
      • Device Discovery tool could become disabled after changing Ethernet parameters on a selected device using the right side of the tool.
      • Network Setup Wizard - Fails setup when a program has a fully numeric Friendly Name.
      • Address Book
        • Address entry from "Pencil" would not allow an address book selection with SSH or SSL
        • Added help button
        • New entries now placed under current selection.
        • Added a field to specify user name
  • DM Tool
    • DMC-STR support and new DMC-STRO support.
  • DMPS Tool
    • DMPS3-200-C and DMPS3-300-C support
  • EDID Tool
    • No Tool changes
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.36.417 (10-2-14)
  • Core Toolbox
    • Notes
      • Removed official support for Windows XP
      • Updated End-user License Agreement
    • New Features
      • SSH/SFTP support.
        • You must select "SSH" check box in the address in order to make use of SFTP transfers. No automatic redirect at this time.
        • Enabled for 3-Series Control Systems and TSX touch screens.
    • New device support
      • HD-MD8x1/8x2 New EDID Management Support
      • CSM-QMTDC-256-2-EX
      • Additional DGE-2 Firmware Update Support
    • Bugs Fixed
      • Added "Setup..." menu support to TST-xx2 and TSW-xx2 devices.
      • Fixed "Renew..." button on Ethernet configuration dialog on some devices where an error would be reported.
      • Ensure passwords are hidden in address book list UI.
      • Fixed crash triggered when using the DNS configuration dialog.
      • Many fixes in Network Setup Wizard for stability and reliability issues.
      • Toolbox crash/locking up when installed on a Win 8.0/8.1 PC
      • Ethernet IP Table dialog for control systems with more than one program did not automatically get information from the device when opened.
      • InfiNet (EX) Gateway Dialog crashed if no devices are acquired
  • DM Tool
    • New EDID mechanism for DM-TX-201-C, DM-TX-401-C, and DM-TX-200-C-2G
    • When saving the Test Report, remember the last used folder.
    • Re-sized the Custom EDID configuration dialog to show fully on x786 screen resolutions.
    • Added DM-TX-401 front panel lockout support.
  • DMPS Tool
    • When saving the Test Report, remember the last used folder.
  • EDID Tool
    • No Tool changes
  • Power Management Tool (CEN-UPS1250)
    • No Tool Changes
  • Device Learner
    • No Tool Changes
  • Sonnex Tool
    • No Tool Changes
  • PROCISE Tool
    • No Tool Changes
  • DVPHD Tool
    • No Tool Changes
  • BPC8 Tool
    • No Tool Changes
  • DALI Commissioning Tool
    • No Tool Changes
  • ProSound Tools
    • No Tool Changes
  • Prodigy Tools
    • No Tool Changes
  • HDXSP Tool
    • No Tool Changes
Toolbox 2.38.226 (8-19-14)
Toolbox 2.36.913 (5-19-14)
Toolbox 2.36.854 (3-28-14)
Toolbox 2.36.814 (3-17-14)
Toolbox 2.36.715 (2-13-14)
Toolbox 2.36.617 (1-22-14)
Toolbox 2.36.541 (1-8-14)
Toolbox 2.36.318 (9-23-2013)
Toolbox 2.36.216 (8-21-2013)
Toolbox 2.36.102 (7-15-2013)
Toolbox 2.36.053 (5-16-2013)
Toolbox 2.35.241 (4-11-2013)
  • Added Support for Crestron App
  • DMPS Tool - Fixed audio compensation on DM Input on DMPS-200-C
Toolbox 2.35.238 (4-5-2013)
Toolbox 2.35.100 (2-7-2013)
Toolbox 2.34.069 (10-10-12)

IMPORTANT - Toolbox is now UAC compliant! This resulted in some improvements and a few changes in file handling. Please read the following list to understand how this may affect your use of Toolbox.

Toolbox 2.33.051(7-20-12)
Toolbox 2.32.053 (4-30-12)
Toolbox 2.31.034 (3-12-12)
Crestron
Crestron Electronics, Inc.
Rockleigh, NJ 07647
Tel: 800.237.2041/ 201.767.3400