Products

    Pages

        CLXI-4HSW4

        4 Channel High-Inrush Switch Module, 4 Feeds - International Version, 230V

        As part of a complete Crestron lighting system, the CLXI-4HSW4 module provides 4 independent channels of switching for high-inrush loads such as motors, HID lighting, and fluorescent ballasts, as well as incandescent, low-voltage, and neon/cold cathode lighting. Each channel is rated for 16 Amps or 1 HP, with a total module rating of 64 Amps when fed from four separate 16 Amp feeds. Air-gap relays are provided on every channel output allowing individual circuits to be serviced without disabling the entire module.

        As part of a complete Crestron lighting system, the CLXI-4HSW4 module provides 4 independent channels of switching for high-inrush loads such as motors, HID lighting, and fluorescent ballasts, as well as incandescent, low-voltage, and neon/cold cathode lighting. Each channel is rated for 16 Amps or 1 HP, with a total module rating of 64 Amps when fed from four separate 16 Amp feeds. Air-gap relays are provided on every channel output allowing individual circuits to be serviced without disabling the entire module.

        An override feature allows each channel to be set to a preset state during setup. In the event that Cresnet communications should be disrupted for any reason, a simple contact closure can be used to activate the override presets on a global or semi-global basis.

        The CLXI-4HSW4 occupies a single module space in any CAEN or CAENIB automation enclosure. Termination of high-voltage wiring to the module is facilitated by a CLTI-4HSW4 terminal block, sold separately to enable termination of the wiring anytime prior to installing the module. CLXI modules are controlled by the PAC2 and PAC2M professional automation control systems via the Cresnet network. A 5-wire link provides bussing of the Cresnet and override signals between modules within an enclosure (interconnect jumpers included).

         
         
        Load Ratings
          Switch Channels 4
          Per Channel 16 Amps, 1 HP
          Module Total 64 Amps
          Load Types Incandescent, Fluorescent, Low-voltage, Neon/Cold Cathode, High-Intensity Discharge (HID), Motors
        Power Requirements
          230 Volts AC, 50/60Hz
        Connectors on Module
          Module Interconnect (2) 5-pin 0.156 inch headers;
        Cresnet/Override interconnect ports;
        Connect to PAC2, PAC2M, CAEN-BLOCK, or adjacent CLXI-Series module using interconnect cable provided
        Connections via CLTI or CLTIBN Terminal Block (sold separately)
          LINE 1 - 4 (4) DIN rail terminal blocks, brown, line power inputs
          SW 1 - 4 (4) DIN rail terminal blocks, red, channel outputs
          N IN 1 - 4 (4) DIN rail terminal blocks, blue, line input neutrals
          N OUT 1 - 4 (4) DIN rail terminal blocks, blue, channel output neutrals
        Buttons
          SETUP Used for manual channel activation and TSID
        LED Indicators
          PWR (green) Indicates line power is applied to the LINE terminal
          NET (yellow) Indicates communication with the control system
          1 – 4 (red x4) Indicates state of each channel
          SETUP (red) Indicates unit is in setup/manual mode
        Environmental
          Temperature 32° to 104°F (0° to 40°C)
          Humidity 10% to 90% RH (non-condensing)
          Heat Dissipation 42 BTU/Hr at maximum load
        Enclosure
          Gray metal with black heat sink, surface mount module with (2) integral mounting flanges;
        Occupies 1 module space in any CAEN or CAENIB enclosure
        Dimensions
          Height 7.59 in (19.27 cm)
          Width 6.92 in (17.57 cm)
          Depth 3.43 in (8.70 cm)
        Weight
          3.00 lb (1.36 kg)