Products

    Pages

        GLXP-DIMFLV8

        8 Channel 0-10V Dimmer Module

        • 8 channels of 0-10 Volt dimming control
        • Compatible with lighting and motor loads
        • Supports 100 to 277 Volt applications

        Visit the Crestron® Lighting Fixture Compatibility page to find out which Crestron lighting devices have been tested and are compatible with third party lighting fixtures.

         

        The GLXP-DIMFLV8 is a Crestron Green Light® switching module that features 8 channels of 0-10 Volt dimming control. This module is part of a complete Crestron® engineered GLPS Green Light switching panel. The GLXP-DIMFLV8-LP model for Green Light Express® systems offers the same functions as the GLXP-DIMFLV8 but with a slightly smaller form factor.

        For more information on Crestron Green Light commercial lighting products, please contact Crestron Sales Support Services.

         
        Key Features
        • 8 channels of 0-10 Volt dimming control
        • Compatible with lighting and motor loads
        • Support for 100 to 277 Volt applications
        • 16 Amp load rating per channel
        • Arc-less switching
        • Positive air gap at each output
        • Phase-independent channels
        • Cresnet® communications
        • Redundant power capability—module powered via line or Cresnet
        • Local controls for testing and verification
        • Local and remote override capability
        • Non-volatile power failure memory
        • GLEP or GLEX[1] cabinet installation
        • CEC Title 24 2013 Compliant
        1. Applies to the GLXP-DIMFLV8-LP model only.
        2. Line power terminal blocks accept 10-14 AWG wire, torque to 4.43lb-in (0.5 Nm).
        3. Terminal blocks for 0-10V connections accept 12-28 AWG wire, torque to 4.43 lb-in (0.5 Nm).

        This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

         

         
        Load Ratings
          Dimmer Channels 8
          Per Channel 16 Amps @ 100 to 277 Volts AC, 50/60 Hz;
        0.5 HP @ 120 Volts, 1 HP @ 230 Volts, 1 HP @ 277 Volts
          Dim Load Types 0-10 Volt fluorescent ballast or LED driver (4-wire);
        60 mA max current sink
          Switch Load Types Incandescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, fluorescent, high-intensity discharge (HID), motors
          Relay Lifetime 1,000,000 on/off operations at full electronic ballast load
        Power Requirements
          Primary 100-277 Volts AC, 50/60Hz, supplied via channel 1 (L1, N1)
          Secondary (optional) 5 Watts at 24 Volts DC, supplied via Cresnet®
        Connectors
          NET (2) 5-pin headers
          N1 (1) Terminal block, line input neutral
          L1-L8 (8) Terminal blocks,[2] line power inputs
          SW1-SW8 (8) Terminal blocks, switch channel outputs
          0-10V DIM (-) (1) 8-position terminal block,[3] dim channel common, galvanically isolated;
        May be wired as Class 1 or Class 2
          0-10V DIM (+) (1) 8-position terminal block,[3] dim channel output, galvanically isolated;
        May be wired as Class 1 or Class 2
        Controls & Indicators
          NET ID (2) 7-segment green LED digits and (2) miniature pushbuttons, sets Cresnet ID;
        Digits also display output levels during local control
          SETUP (1) Red LED and (1) recessed miniature pushbutton, enables setup mode and touch-settable ID
          OVR (1) Red LED and (1) miniature pushbutton, enables override mode and saves override presets
          PWR (1) Green LED, indicates power status;
        Solid illumination indicates line power is applied to N1 and L1;
        Flashing indicates Cresnet power is supplied in absence of line power
          NET (1) Yellow LED, indicates communication with control processor
          RESET (1) Recessed miniature pushbutton, resets internal processor
          ON/OFF (8) Red LEDs and (8) miniature pushbuttons, manually activates individual channels for dimming
        Enclosure
          Surface-mount module with (2) integral mounting flanges;
        GLXP-DIMFLV8 model mounts in a GLEP enclosure;
        GLXP-DIMFLV8-LP model mounts in a GLEX enclosure
        Environmental
          Temperature 32° to 104° F (0° to 40° C)
          Humidity 10% to 90% RH (non-condensing)
          Heat Dissipation 116 BTU/Hr
        Dimensions
          Height 11.07 in (282 mm)
          Width 9.5 in (241 mm) including mounting holes
          Depth (GLXP-DIMFLV8) 4.78 in (121 mm) including standoffs
          Depth (GLXP-DIMFLV8-LP) 3.26 in (82 mm)
        Electrical Regulatory Certifications
          UL508, Section 41 (Endurance Test) and Section 61C (Electronic Ballasts)
          UL924, Emergency Power Equipment
          IEC60669-2-1, Section 19.102 (Contact mechanisms incorporated in electronic switches, intended for fluorescent lamp circuits or other capacitive loads)
          SCCR Rating - 65kA
          CE
          CEC Title 24 2013 Compliant
        1. Applies to the GLXP-DIMFLV8-LP model only.
        2. Line power terminal blocks accept 10-14 AWG wire, torque to 4.43lb-in (0.5 Nm).
        3. Terminal blocks for 0-10V connections accept 12-28 AWG wire, torque to 4.43 lb-in (0.5 Nm).

        This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.