Products

    Pages

        CLXI-2DIM2

        2 Channel Dimmer Module, 2 Feeds - International Version, 230V

        Provides 2 independent channels of dimming for 230V incandescent, magnetic low-voltage, neon/cold cathode, and dimmable 2-wire fluorescent loads. Each channel is rated for 2300 Watts, with a total module rating of 4600 Watts when fed from two separate 16 Amp feeds. Air-gap relays are provided on each channel output to allow an individual circuit to be serviced without disabling the entire module.

        Visit the Crestron® Lighting Fixture Compatibility page to find out which Crestron lighting devices have been tested and are compatible with third party lighting fixtures.

        As part of a complete Crestron lighting system, the CLXI-2DIM2 lighting control module provides 2 independent channels of dimming for 230V incandescent, magnetic low-voltage, neon/cold cathode, and dimmable 2-wire fluorescent loads. Each channel is rated for 2300 Watts, with a total module rating of 4600 Watts when fed from two separate 16 Amp feeds. Air-gap relays are provided on each channel output to allow an individual circuit to be serviced without disabling the entire module.

        CLXI-Series dimmers are rigorously built using 40 Amp triacs and oversized heat sinks for ultimate reliability. Split-bobbin transformers and ground-referenced electronics deliver superior performance. Lamp flicker is minimized through Crestron's innovative zero-crossing detection technique, backed by proprietary firmware. Low-maintenance convection cooling assures quiet and trouble-free operation.

        An override feature allows each channel to be adjusted to a preset state during setup. In the event that Cresnet® communications should be disrupted for any reason, a simple contact closure can be used to activate the override presets.

        The CLXI-2DIM2 occupies a single module space in any CAEN or CAENIB automation enclosure. Termination of high-voltage wiring to the module is facilitated by a CLTI-2DIM2 terminal block, sold separately to enable termination of the wiring at any time prior to installing the module. CLXI modules are controlled by the PAC2 and PAC2M professional automation control systems via the Cresnet network. A 5-wire link provides bussing of the Cresnet and override signals between modules within an enclosure (interconnect jumpers included).

         

        This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

         

        The specific patents that cover Crestron products are listed online at: patents.crestron.com.

         

        Crestron, the Crestron logo, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2015 Crestron Electronics, Inc.

         
        Load Ratings
          Dimmer Channels 2
          Per Channel 10 Amps (2300 Watts)
          Module Total 20 Amps (4600 Watts)
          Load Types Incandescent, Magnetic Low-voltage, Neon/Cold Cathode, Dimmable 2-Wire Fluorescent
          Minimum Load 15 Watts
        Power Requirements
          230 Volts AC, 50/60Hz, single-phase;
        All feeds must be same phase or split phase
        Connectors on Module
          Module Interconnect (2) 5-pin 0.156 inch headers;
        Cresnet/Override interconnect ports;
        Connect to PAC2, PAC2M, CAEN-BLOCK, or adjacent CLXI-Series module using interconnect cable provided
        Connections via CLTI or CLTIBN Terminal Block (Sold Separately)
          LINE 1 - 2 (2) DIN rail terminal blocks, brown, line power inputs;
        Must be same phase or split phase
          DIM 1 - 2 (2) DIN rail terminal blocks, red, channel outputs
          N IN 1 - 2 (2) DIN rail terminal blocks, blue, line input neutrals
          N OUT 1 - 2 (2) DIN rail terminal blocks, blue, channel output neutrals
        Buttons
          SETUP Used for manual channel activation and TSID
        LED Indicators
          PWR (1) Green LED, indicates line power is applied to the LINE terminal
          NET (1) Yellow LED, indicates communication with the control system
          1 – 2 (2) Red LEDs, each indicates the state of the corresponding channel
          SETUP (1) Red LED, indicates unit is in setup/manual mode
        Environmental
          Temperature 32° to 104° F (0° to 40° C)
          Humidity 10% to 90% RH (non-condensing)
          Heat Dissipation 114 BTU/Hr at maximum load
        Enclosure
          Gray metal with black heat sink, surface mount module with (2) integral mounting flanges;
        Occupies 1 module space in any CAEN or CAENIB enclosure
        Dimensions
          Height 7.59 in (193 mm)
          Width 6.92 in (176 mm)
          Depth 3.43 in (87 mm)
        Weight
          3.00 lb (1.36 kg)

        This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

         

        The specific patents that cover Crestron products are listed online at: patents.crestron.com.

         

        Crestron, the Crestron logo, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2015 Crestron Electronics, Inc.