Products

    Pages

        C2N-IO

        Control Port Expansion Module

        An outboard module for adding control ports to a Crestron® touch screen control system or any other Crestron control systems.

        The C2N-IO is a very compact device that adds control ports to any Crestron® 2-Series or 3-Series® control system. It connects via the Cresnet® control network and provides one RS-232, one IR, and two relay control ports.[1] It can be mounted to any flat surface using two screws or adhesive reclosable fastener (3M® Dual Lock® included).

        The C2N-IO is ideally designed for use with a Crestron touch screen control system ( TPCS-4SM, TPCS-4SMD, or TSCW-730), providing an advanced wall mount control package that fits in a 2-gang US or UK electrical box. The C2N-IO can be mounted inside the electrical box behind the touch screen, or it can be installed remotely requiring just one Cresnet control cable for power and communications.

         
        Key Features
        • Fits within a 2-gang wall box behind the TPCS-4SM(D) or TSCW-730
        • Provides 1 RS-232, 1 IR/serial, and 2 relay ports [1]
        • Compatible with any Crestron® 2-Series or 3-Series® control system
        • Interfaces via the Cresnet® control bus
        • 24 Volt DC Cresnet powered
        • Surface mount bracket included
        1. The RS-232 COM port is intended for use with relatively simple devices that send and receive small packets and do not generate a lot of data. A small amount of delay may be normal when sending or receiving some control commands on a low-speed serial network. Cresnet networks with many devices tend to exhibit more delay.

        This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

        The specific patents that cover Crestron products are listed online at: patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, 3-Series, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. 3M and Dual Lock are either trademarks or registered trademarks of 3M Company in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2015 Crestron Electronics, Inc.

         
        Communications
          Cresnet® Cresnet slave device, 2-Series and 3-Series® compatible
          RS-232 Supports 2-way device control and monitoring up to 115.2k baud with software handshaking [1]
          IR/Serial Supports 1-way device control via infrared up to 1.2 MHz or serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
        Connectors
          RELAY 1 – 2 (1) 4-pin captive screw terminal block comprising (2) normally open, isolated relays;
        Rated 1 Amp, 30 Volts AC/DC;
        Solid-state arc suppression across contacts
          COM (1) 3-pin captive screw terminal block, bidirectional RS-232 port [1];
        Up to 115.2k baud; software handshaking support
          IR (1) 2-pin captive screw terminal block, IR/Serial output port;
        IR output up to 1.2 MHz;
        1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
          NET (2) 4-pin captive screw terminal blocks;
        Cresnet slave ports, paralleled
        Controls & Indicators
          NET ID (2) Rotary switches for manually setting Cresnet ID;
        '00' setting enables touch-settable ID (TSID)
          PWR (1) Green LED, indicates operating power supplied via Cresnet control network
          NET (1) Amber LED, indicates communication with Cresnet system
          SETUP (1) Red LED and (1) recessed miniature pushbutton for TSID
        Power Requirements
          Cresnet Power Usage 2.5 Watts (105 mA @ 24 Volts DC)
        Environmental
          Temperature 32° to 104° F (0° to 40° C)
          Humidity 10% to 90% RH (non-condensing)
          Heat Dissipation 3.5 BTU/hr
        Enclosure
          Metal, freestanding or surface mount, surface mount bracket and 3M® Dual Lock® reclosable fastener included, fits inside a 2-gang electrical box or 2-gang UK (BS 4662) electrical box, 1.38 in (35 mm) minimum internal box depth required for C2N-IO and TPCS-4SM(D) or TSCW-730 combined
        Dimensions
          Height 2.25 in (58 mm)
          Width 3.50 in (89 mm), 4.38 in (112 mm) with bracket
          Depth 0.83 in (21 mm)
        Weight
          2.7 oz (75 g)
        1. The RS-232 COM port is intended for use with relatively simple devices that send and receive small packets and do not generate a lot of data. A small amount of delay may be normal when sending or receiving some control commands on a low-speed serial network. Cresnet networks with many devices tend to exhibit more delay.

        This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

        The specific patents that cover Crestron products are listed online at: patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, 3-Series, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. 3M and Dual Lock are either trademarks or registered trademarks of 3M Company in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2015 Crestron Electronics, Inc.

        Online Help

        What devices can I connect to a C2N-IO?
        Online Help Answer ID :5603