Products

    Pages

         

        HD-TX-4KZ-211-2G-B

        DM Lite® 4K60 4:4:4 Transmitter and 2x1 Auto-Switcher for HDMI® and USB-C® DisplayPort™ Signal Extension over CATx Cable, Wall Plate, Black

        Interoperability with a DM Lite® receiver or DMPS Lite™ switcher to provide point-to-point extension of an HDMI® or USB-C® DisplayPort™ signal over a CATx cable. Supports 4K60 4:4:4 video, HDR10+, and HDCP 2.3. Provides one HDMI input and one USB-C DisplayPort input with automatic switching capability. Mounts into a 2-gang electrical box.

        Faceplate sold separately.

        Limited Supply Available

        The HD-TX-4KZ-211-2G is a DM Lite® 4K60 4:4:4 wall plate transmitter designed to interoperate with a DM Lite® receiver or DMPS Lite™ switcher. The paired transmitter and receiver enable extension of HDMI® or USB-C® DisplayPort™ AV signals. This is useful in applications where an AV source is located remotely from its destination, such as a display, projector, or codec solution. A CAT5e or higher twisted pair cable must be used to connect the HD-TX-4KZ-211-2G to the DM Lite receiver or DMPS Lite switcher.1

        The HD‑TX‑4KZ‑211‑2G is available in two models: HD‑TX‑4KZ‑211‑2G-B (black) and HD‑TX‑4KZ‑211‑2G-W (white).

        Interoperability with a DM Lite Receiver or DMPS Lite Switcher
        The DM Lite output port of the HD-TX-4KZ-211-2G must be connected to a DM Lite input port of a DM Lite 4K60 4:4:4 receiver, DM Lite 4K60 4:2:0 receiver, or DMPS Lite switcher.

        The HD-TX-4KZ-211-2G can be configured and controlled only when it is used with a DMPS Lite switcher. The web interface of the switcher can be used to configure the HD-TX-4KZ-211-2G. In addition, control system programming and .AV Framework™ software support of the HD-TX-4KZ-211-2G is hosted by the switcher.

        4K60 4:4:4 and HDR Support
        The HD-TX-4KZ-211-2G supports video resolutions up to 4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby Vision® video formats are also supported.2

        Automatic Switching of Inputs
        When the HD-TX-4KZ-211-2G is used with a DMPS Lite switcher, the web interface of the switcher or control system programming hosted by the switcher can be used to configure AV switching behavior. Switching between the HDMI and USB-C DisplayPort inputs occurs based on the last connected input or on the routing priority assigned to each input. In addition, the input selection push button on the front of the HD-TX-4KZ-211-2G enables the desired input to be selected manually.

        Two-Gang Wall Plate Design
        The HD‑TX‑4KZ-211-2G is designed to mount into a 2-gang U.S. electrical box or plaster ring (not included). The HD‑TX‑4KZ‑211‑2G can receive power from the remote DM Lite receiver (surface mountable only) or DMPS Lite switcher.3

         
        Key Features
        • Interoperability with a DM Lite® receiver or DMPS Lite™ switcher
        • Point-to-point extension of an HDMI® or USB-C® DisplayPort™ signal over a CAT5e or higher cable
        • USB-C input with DisplayPort Alt Mode capability
        • DM Lite transmission distance up to 130 ft (40 m) for UHD and 4K signals or up to 230 ft (70 m) for 1080p, WUXGA, and 2K signals
        • 4K60 4:4:4 capability
        • HDR10, HDR10+, and Dolby Vision® video formats
        • Compliance with HDCP 2.3
        • Automatic switching of HDMI and USB-C DisplayPort inputs
        • CEC (Consumer Electronics Control) pass-through capability
        • EDID pass-through capability
        • Two-gang wall plate design with black finish
        • Decorator style faceplate required (FP-G2-DM Series sold separately)
        • Power from the remote DM Lite receiver (surface mountable only) or DMPS Lite switcher
        1. For DM Lite connections, use Crestron DM-CBL-8G, Crestron DM‑CBL‑ULTRA, or third-party CAT5e or higher cable. To safeguard against unpredictable environmental electrical noise that may impact performance at resolutions above 1080p, shielded cable and connectors are recommended for all applications and are required when bundling multiple cables in a wire run. Cables are sold separately.
        2. For HDMI inputs, 4K60 4:4:4 performance and HDR support require the use of HDMI cables and couplers with a minimum TMDS bandwidth of 18 Gbps. If 4K60 4:2:0 or 4K30 4:4:4 performance is acceptable, cables and couplers with a minimum bandwidth of 10.2 Gbps may be used. Bandwidth loss is cumulative; therefore, performance may be reduced when inserting multiple cables and couplers inline.

          For USB-C DisplayPort inputs, 4K60 4:4:4 performance and HDR support require the use of USB 3.2 Gen 1 (5 Gbps) cables with support for DisplayPort Alt Mode (DisplayPort 1.4 video, 4K60 4:4:4, 2 lanes). Cables are sold separately.
        3. When a DM Lite wall plate transmitter is paired with a DM Lite surface-mountable receiver, the power pack included with the receiver is used to power both devices.

          When a DM Lite transmitter is paired with a DMPS Lite switcher, the switcher provides power to the DM Lite transmitter.

          If a wall plate transmitter is paired with a wall plate receiver, the devices must be powered independently by a PW-2407WUL power pack (sold separately) for each device. A wall plate transmitter and wall plate receiver cannot provide power to the remote device with which it is paired.
        4. The HDMI input requires an appropriate adapter or interface cable to accommodate a Dual-Mode DisplayPort or DVI signal. CBL-HD-DVI interface cables are sold separately.
        5. CBL-USB3G1-C-C-6 and CBL-USB3G2-C-C-3 cables are sold separately.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or contact us for additional information by visiting www.crestron.com/contact/our-locations for your local contact.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open-source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, .AV Framework, DM Lite, and DMPS Lite are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, Dolby Digital, and Dolby Vision are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries. DTS, DTS HD, and DTS:X are either trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Intertek and the Intertek logo are either trademarks or registered trademarks of Intertek Group in the United States and/or other countries. USB Type-C and USB C are either trademarks or registered trademarks of USB Implementers Forum, Inc. in the United States and/or other countries. DisplayPort is either a trademark or registered trademark of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2023 Crestron Electronics, Inc.

         
        4K HDMI AVF Works With (2) HDCP 2.3
        Video
        Input Signal Types HDMI® (DVI and Dual-Mode DisplayPort™ interface compatible4) and DisplayPort over USB-C® (DisplayPort Alt Mode) with HDR10, HDR10+, Dolby Vision®, Deep Color, and 4K60 4:4:4 support2
        Output Signal Type DM Lite® with HDR10, HDR10+, Dolby Vision, Deep Color, and 4K60 4:4:4 support2
        Copy Protection HDCP 2.3
        Resolutions Common resolutions are listed in the following table.
        Scan Type Resolution Frame Rate Color Sampling Color Depth
        Progressive 4096x2160 DCI 4K & 3840x2160 4K UHD 24 Hz 4:4:4 12 bit
        30 Hz 4:4:4 12 bit
        60 Hz 4:2:2 12 bit
        60 Hz 4:4:4 8 bit
        2560x1600 WQXGA 60 Hz 4:4:4 8 bit
        1920x1080 FHD 1080p 60 Hz 4:4:4 12 bit
        Interlaced (HDMI input only) 1920x1080 HD 1080i 30 Hz 4:4:4 12 bit
        Notes: The maximum supported resolution is 4K60 with 4:4:4 color sampling. Custom resolutions are supported at pixel clock rates up to 600 MHz. The USB-C DisplayPort input does not support interlaced video.
        Audio
        Input Signal Types HDMI, DisplayPort over USB-C (DisplayPort Alt Mode)
        Output Signal Type DM Lite
        Digital Formats Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby® TrueHD, Dolby Atmos®, DTS®, DTS ES, DTS 96/24, DTS HD® High Res, DTS-HD Master Audio, DTS:X®, LPCM up to 8 channels
        Communications
        HDMI HDCP 2.3, EDID, CEC pass-through
        USB‑C HDCP 2.3, EDID, CEC pass-through
        DM Lite HDCP 2.3, EDID pass-through
        Connectors
        HDMI IN (1) HDMI Type A connector, female;
        HDMI digital video/audio input;
        DVI and Dual-Mode DisplayPort interface compatible4
        USB IN (1) USB Type‑C® connector, female;
        Digital video/audio input using DisplayPort Alt Mode5
        DM LITE OUT (1) 8‑pin RJ‑45 yellow connector, female, shielded;
        DM Lite output port for connection to a DM Lite receiver or DMPS Lite™ switcher1
        24V 0.7A (1) 2-pin 3.5 mm detachable terminal block;
        24VDC power input;
        Power pack sold separately, required only if the HD-TX-4KZ-211-2G is used with a wall plate receiver3
        Ground (1) Chassis ground lug
        Controls and Indicators
        PWR (1) LED, indicates that power is being applied to the device. Amber indicates that the device is booting. Green indicates that the device is operational.
        AUTO (1) Push button for enabling or disabling automatic switching of inputs;
        (1) LED, green indicates that automatic switching of inputs is enabled
        SETUP (1) Push button for Ethernet setup (applicable only when used with a DMPS Lite switcher);
        (1) LED, red indicates that the SETUP push button is pressed
        LINK (1) LED, green indicates that a DM Lite link is established
        INPUT (1) Push button for manual input selection
        HDMI IN (1) LED, green indicates that the HDMI input is routed to an output, and amber indicates that a source is detected but is not routed to an output
        USB IN (1) LED, green indicates that the USB-C DisplayPort input is routed to an output, and amber indicates that a source is detected but is not routed to an output
        RESET (1) Push button for restoring the device to factory default settings
        DM LITE OUT (2) LEDs on RJ‑45 connector.
        Green indicates that a DM Lite link is established;
        Flashing amber indicates non‑HDCP video, and solid amber indicates HDCP video.
        Power
        Power Pack Input: 100-240VAC
        Output: 24VDC 0.75A
        Model: PW-2407WUL (sold separately, required only if the HD-TX-4KZ-211-2G is used with a wall plate receiver)3
        Environmental
        Temperature 32° to 104°F (0° to 40°C)
        Humidity 20% to 90% RH (non-condensing)
        Construction
        Composition Metal housing and bracket with black polycarbonate front label overlay
        Mounting Mounts in a 2-gang (or larger) 2-inch (51 mm) deep U.S. electrical box or plaster ring (not included)
        Faceplate Requires a decorator style faceplate (FP-G2-DM Series, sold separately)
        Dimensions
        Height 4.12 in. (105 mm)
        Width 3.57 in. (91 mm)
        Depth 1.66 in. (42 mm)
        Weight
        7.33 oz (208 g)
        Compliance
        Regulatory Model: M202046004
        Intertek® Listed for US and Canada, CE, IC, FCC Part 15 Class A digital device
        Maximum DM Lite Transmission Distance
        Resolution Frame Rate (Hz) Color Sampling Color Depth Cable Type1
        DM-CBL-ULTRA DM® Ultra Cable DM-CBL-8G DM 8G® Cable or CAT5e (UTP) or Higher
        1920x1080 HD 1080i 30 4:4:4 12 bit 230 ft (70 m) 195 ft (60 m)
        1920x1080 FHD 1080p 60 4:4:4 8, 12 bit
        1600x1200 UXGA 60 4:4:4 8, 12 bit
        2048x1080 DCI 2K 60 4:4:4 8, 12 bit
        1920x1200 WUXGA 60 4:4:4 8, 12 bit
        2048x1152 QWXGA 60 4:4:4 8, 12 bit
        2560x1080 UWFHD 60 4:4:4 8 bit
        2560x1440 WQHD Reduced Blanking 60 4:4:4 8 bit
        2560x1600 WQXGA Reduced Blanking 60 4:4:4 8 bit
        2048x1152 QWXGA 60 4:4:4 12 bit
        3840x2160 4K UHD and 4096x2160 DCI 4K 30 4:2:2 12 bit
        30 4:4:4 8 bit
        60 4:2:0 8 bit
        3840x2160 4K UHD and 4096x2160 DCI 4K 30 4:4:4 12 bit 130 ft (40 m) 100 ft (30 m)
        60 4:2:0 12 bit
        60 4:2:2 12 bit
        60 4:4:4 8 bit
        Click here to search product certificates.
        1. For DM Lite connections, use Crestron DM-CBL-8G, Crestron DM‑CBL‑ULTRA, or third-party CAT5e or higher cable. To safeguard against unpredictable environmental electrical noise that may impact performance at resolutions above 1080p, shielded cable and connectors are recommended for all applications and are required when bundling multiple cables in a wire run. Cables are sold separately.
        2. For HDMI inputs, 4K60 4:4:4 performance and HDR support require the use of HDMI cables and couplers with a minimum TMDS bandwidth of 18 Gbps. If 4K60 4:2:0 or 4K30 4:4:4 performance is acceptable, cables and couplers with a minimum bandwidth of 10.2 Gbps may be used. Bandwidth loss is cumulative; therefore, performance may be reduced when inserting multiple cables and couplers inline.

          For USB-C DisplayPort inputs, 4K60 4:4:4 performance and HDR support require the use of USB 3.2 Gen 1 (5 Gbps) cables with support for DisplayPort Alt Mode (DisplayPort 1.4 video, 4K60 4:4:4, 2 lanes). Cables are sold separately.
        3. When a DM Lite wall plate transmitter is paired with a DM Lite surface-mountable receiver, the power pack included with the receiver is used to power both devices.

          When a DM Lite transmitter is paired with a DMPS Lite switcher, the switcher provides power to the DM Lite transmitter.

          If a wall plate transmitter is paired with a wall plate receiver, the devices must be powered independently by a PW-2407WUL power pack (sold separately) for each device. A wall plate transmitter and wall plate receiver cannot provide power to the remote device with which it is paired.
        4. The HDMI input requires an appropriate adapter or interface cable to accommodate a Dual-Mode DisplayPort or DVI signal. CBL-HD-DVI interface cables are sold separately.
        5. CBL-USB3G1-C-C-6 and CBL-USB3G2-C-C-3 cables are sold separately.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or contact us for additional information by visiting www.crestron.com/contact/our-locations for your local contact.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open-source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, .AV Framework, DM Lite, and DMPS Lite are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, Dolby Digital, and Dolby Vision are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries. DTS, DTS HD, and DTS:X are either trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Intertek and the Intertek logo are either trademarks or registered trademarks of Intertek Group in the United States and/or other countries. USB Type-C and USB C are either trademarks or registered trademarks of USB Implementers Forum, Inc. in the United States and/or other countries. DisplayPort is either a trademark or registered trademark of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2023 Crestron Electronics, Inc.

        Pricing Region Select
        Please select your region below to see the appropriate Advertised Pricing.