Products

    Pages

        ZUMMESH-JBOX-16A-LV-EM

        Zum™ Mesh Wireless J-Box Emergency Load Controller, 0-10 V Dimmer, 16 A, 100-277 V

        A selection of junction box-mounted load controllers designed to provide intelligent lighting control as part of a complete Zūm™ commercial room lighting system.

        Crestron® Zūm™ Mesh Wireless J-Box Load Controllers (ZUMMESH‑JBOX Series) can provide 20 A switching, 5 A or 16 A 0‑10 V dimming, and 20 A plug load control. J‑Box load controllers mount directly to a 4 in. square junction box. Zūm Mesh wireless technology affords easy pair and play integration as part of a complete Zūm commercial lighting system. Energy‑saving options are available to enable daylighting, occupancy or vacancy sensing, HVAC system integration, and centralized monitoring and management.

        Energy Efficiency
        Occupancy sensor, vacancy sensor, and daylight sensor connectivity allow for significant energy savings. To reduce energy usage, lights will turn off automatically when the room is vacant and dim gradually according to the amount of natural daylight in the room.

        Pair and Play Setup
        Pair and play functionality in Zūm load controllers allows for installation in a room along with Zūm keypads, occupancy or vacancy sensors, and/or a daylight sensor. Set up the room with a few button taps and instantly control the room lights without any additional programming. Room setup can be accomplished via the Zūm app if the room is equipped with a Zūm Network Bridge (sold separately).

        Optional Zūm Network Bridge
        Snap a Zūm Network Bridge (ZUMMESH‑NETBRIDGE, sold separately) onto a Zūm Wireless J-Box Load Controller for centralized lighting management via a Zūm Floor Hub and Zūm Net Wireless Gateway. The Zūm Network Bridge enables enhanced room setup using the Zūm app.

        Optional Contact Closure Output
        Snap a Zūm Contact Closure Output (ZUMMESH‑CCO, sold separately) onto the Zūm Wireless J‑Box Load Controller for integration with an HVAC system or other relay-controlled equipment.

        Zūm Mesh Wireless Technology
        Zūm Mesh wireless technology provides peer-to-peer RF communications within a commercial space without the need for physical control wiring, hubs, or gateways. Nearly every Zūm Mesh device acts as a routing node to relay wireless commands between Zūm Mesh devices without disruption.

        Adding Zūm Mesh devices to a space increases the range and stability of the peer-to-peer mesh network by providing multiple redundant signal paths. Each Zūm Mesh device auto‑negotiates its RF channel to provide robust communication and is protected through AES 128-bit encryption.

        Emergency Load Control
        The ZUMMESH‑JBOX‑16A‑LV‑EM provides load control to meet UL 924 standards. The device functions like a standard J‑box dimmer in normal conditions, where it can bind to keypads, make scene modifications, follow sensor control states, and perform other standard ZUMMESH‑JBOX actions.

        If power to a lighting system is lost, the device enters Emergency Mode for ninety minutes or until system power is restored, whichever comes first. In Emergency Mode, all connected loads are fully illuminated to allow for safe exit from the space.

         
        Key Features
        • Zūm™ wireless junction box-mounted lighting load controllers
        • Pair and play wireless integration with Zūm keypads, occupancy sensors, vacancy sensors, and daylight sensors
        • Zūm Mesh peer-to-peer RF communications for integration into a complete standalone or networked Zūm wireless lighting control solution
        • Dimming control of 0-10 V dimmable LED or fluorescent loads
        • Dimmers rated 5 or 16 A at 100-277 VAC
        • Zero cross switch control of 20 A, 100-277 V high inrush lighting loads
        • Zero cross switch control of 20 A, 100-250 V plug loads
        • Emergency lighting control meets UL® 924 standards
        • Accommodation for a Zūm Network Bridge or Zūm Contact Closure Output device
        • Flying lead wiring connections
        • Knockout mount to a standard 4 in. square junction box
        • UL 2043 listed for installation in an environmental air handling space
        • Meets UL 916 standard for energy management equipment
        • Meets CEC Title 24 and ASHRAE® 90.1 energy efficiency standards
        • ICC® International Energy Conservation Code® compliant
        1. “Zūm Mesh” refers to the peer-to-peer wireless mesh network within a room composed of dimmers, switches, load controllers, keypads, and sensors. “Zūm Net” refers to the wireless mesh network that connects one or more rooms with a Zūm Floor Hub, and consists of a Zūm Net Wireless Gateway and one or more Zūm Network Bridges. AC-powered Zūm Mesh or Zūm Net devices function as routing nodes, which effectively extend the range of a Zūm Mesh or Zūm Net wireless network. Battery-powered devices only function as leaf nodes and do not extend range. A Zūm Mesh network composed predominantly of battery-powered devices may require additional AC-powered devices, such as the ZUMMESH-JBOX-PSU, to serve as supplemental routing nodes to fill any gaps in coverage. Refer to the “Installation and Setup of Crestron RF Products, Best Practices” guide (Doc #6689) for additional guidelines.
        2. Not for use with ZUMMESH‑JBOX‑20A‑PLUG.
        3. For use with ZUMMESH‑JBOX‑5A‑LV and ZUMMESH‑JBOX‑16A‑LV only.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, and Zūm are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. ASHRAE is either a trademark or registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. in the United States and/or other countries. ICC and International Energy Conservation Code are either trademarks or registered trademarks of International Code Council, Inc. in the United States and/or other countries. UL is either a trademark or registered trademark of UL LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.

         
        Load Control - Switch (-SW) and Plug (-PLUG) Models
        Switched Load Types LED, fluorescent ballast, incandescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, high-intensity discharge
        Load Rating ZUMMESH-JBOX-20A-SW: 20 A, high inrush, zero cross switching;
        ZUMMESH-JBOX-20A-PLUG: 20 A (or 16 A derated by 80%), high inrush, zero cross switching for receptacles
        Load Control - Dimming (-LV) Models
        Dimmable Load Types 0-10 V LED drivers or fluorescent ballasts (4-wire), 60 mA maximum current sink
        Load Rating ZUMMESH-JBOX-5A-LV: 5 A;
        ZUMMESH-JBOX-16A-LV: 16 A
        Load Control - Emergency (-EM) Model
        Dimmable Load Types 0-10 V LED drivers or fluorescent ballasts (4-wire), 60 mA maximum current sink
        Load Rating 16 A
        Emergency Mode All loads in the zone fully illuminate for ninety minutes or until normal power is restored (whichever comes first);
        Keypads are disabled;
        Sensors are disabled;
        The TEST button toggles the connected load on and off when pressed;
        Exits emergency mode when normal power is restored or after ninety minutes have passed;
        System communications return when normal power is restored
        Power Requirements
        Line/Load Voltage 100-277 VAC, 50/60 Hz
        Line/Load Voltage (-PLUG model only) 125/250 VAC, 50/60 Hz, UL rating per UL 498;
        100-250 VAC, 50/60 Hz, operating range
        Dim Control Output (-LV models only) 0-10 VDC, 60 mA maximum sink or source
        Idle Power Consumption 1 W
        Wireless Communications
        RF Transceiver Zūm Mesh & Zūm Net 2-way RF, 2.4 GHz ISM Channels 15, 20, 25, or 26 (channel auto-selected), IEEE 802.15.4 compliant
        Zūm Mesh Range 50 ft (15 m) to nearest peer-to-peer mesh network device(s), subject to site-specific conditions and individual device capabilities [1]
        Zūm Net Range 50 ft (15 m) to a Zūm Net wireless gateway or nearest Zūm Net mesh network device(s), requires the Zūm Network Bridge (model ZUMMESH-NETBRIDGE, sold separately), range between floors or ceilings is limited to one level, subject to site-specific conditions and individual device capabilities [1]
        Note: A maximum of 32 Zūm Mesh wireless devices is permitted per room. Only one Network Bridge is permitted per room.
        Controls & Indicators
        SETUP (1) Pushbutton and (1) red LED, used for room setup and factory reset
        TEST (1) Pushbutton and (1) green LED;
        Push to toggle the switched load output on and off;
        Press and hold the button to cycle the dimming level up and down;
        LED indicates that the load is turned on;
        LED lights and flashes during room setup and factory reset
        Connections
        Hot (1) 14 AWG Class 1 flying lead;
        Black, line power input
        Neutral (1) 14 AWG Class 1 flying lead;
        White, neutral
        0-10 V Dim +,
        0-10 V Dim -,
        (-LV models only)
        (2) 18 AWG Class 1 flying lead;
        Purple, 0-10 VDC dimming control output, positive;
        Gray, 0-10 VDC dimming control output, negative
        Switched Load (1) 14 AWG Class 1 flying lead;
        Red, switched load output
        Expansion Port Accessory port for expansion accessory;
        ZUMMESH-NETBRIDGE: Provides Zūm Net wireless communications (sold separately);
        ZUMMESH-CCO: Provides contact closure input (sold separately)
        Environmental
        Temperature 32° to 104° F (0° to 40° C)
        Humidity 10% to 90% RH (noncondensing)
        Construction
        Housing Plastic, white, UL 94 5VA flame rated
        Mounting Mounts to the side of a 4-inch square junction box via a 1/2 in. conduit knockout;
        Meets the requirements of UL 2043 for installation in an environmental air-handling (plenum) space;
        To meet Chicago plenum requirements, install the J-box in a ZUMMESH-JBOX-FMKT-CP enclosure
        Dimensions
        Height 3.25 in (83 mm)
        Width 4.17 in (106 mm);
        Projects 3.66 in. (93 mm) from the junction box when installed
        Depth 1.32 in (34 mm)
        Weight
        7 oz (199 g)
        Compliance
        UL Listed for US & Canada, IC, FCC Part 15 Class A digital device, UL 916, UL 924 (-EM model only), UL 2043, UL 94 5VA
        1. “Zūm Mesh” refers to the peer-to-peer wireless mesh network within a room composed of dimmers, switches, load controllers, keypads, and sensors. “Zūm Net” refers to the wireless mesh network that connects one or more rooms with a Zūm Floor Hub, and consists of a Zūm Net Wireless Gateway and one or more Zūm Network Bridges. AC-powered Zūm Mesh or Zūm Net devices function as routing nodes, which effectively extend the range of a Zūm Mesh or Zūm Net wireless network. Battery-powered devices only function as leaf nodes and do not extend range. A Zūm Mesh network composed predominantly of battery-powered devices may require additional AC-powered devices, such as the ZUMMESH-JBOX-PSU, to serve as supplemental routing nodes to fill any gaps in coverage. Refer to the “Installation and Setup of Crestron RF Products, Best Practices” guide (Doc #6689) for additional guidelines.
        2. Not for use with ZUMMESH‑JBOX‑20A‑PLUG.
        3. For use with ZUMMESH‑JBOX‑5A‑LV and ZUMMESH‑JBOX‑16A‑LV only.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, and Zūm are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. ASHRAE is either a trademark or registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. in the United States and/or other countries. ICC and International Energy Conservation Code are either trademarks or registered trademarks of International Code Council, Inc. in the United States and/or other countries. UL is either a trademark or registered trademark of UL LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.