12 Channel High-Inrush Switch Module
This product has been discontinued. Please contact Crestron True Blue Support at 1-888-CRESTRON for a replacement solution or more information.
Replace With GLXP-HSW12-LP
- 12 channels of high-inrush power switching
- Rugged, high-current latching relays
- Supports 100 to 277 Volt applications
The GLXP-HSW12 is a Crestron® Green Light® switching module which features 12 channels of high-inrush power switching with rugged, high-current latching relays. The module is part of a complete Crestron engineered GLPS
Green Light switching panel.
For more information on Crestron Green Light commercial lighting products, please contact Crestron Sales Support Services.
Key Features
- 12 channels of high-inrush power switching
- Rugged, high-current latching relays
- Supports 100 to 277 Volt applications
- 16 Amp, 1 HP load rating per channel
- Arc-less switching
- Positive air gap at each output
- Phase-independent channels
- Cresnet® communications
- Redundant power capability—module powered via line or Cresnet
- Local controls for testing and verification
- Local and remote override capability
- Non-volatile power failure memory
- GLEP cabinet installation
Load Ratings |
|
Switch Channels |
12 |
|
Per Channel |
16 Amps @ 100 to 277 Volts AC, 50/60 Hz;
0.5 HP @ 120 Volts, 1 HP @ 230 Volts, 1 HP @ 277 Volts |
|
Switch Load Types |
Incandescent, Magnetic Low-Voltage, Electronic Low-Voltage, Neon/Cold Cathode, Fluorescent Ballast, High-Intensity Discharge, LED, Motor |
|
Relay Lifetime |
1,000,000 on/off operations at full electronic ballast load |
Power Requirements |
|
Primary |
100-277 Volts AC, 50/60Hz, supplied via channel 1 (L1, N1) |
|
Secondary (optional) |
5 watts at 24 Volts DC, supplied via Cresnet® |
Connectors |
|
NET |
(2) 5-pin headers; connect to adjacent module or internal connecting block using interconnect cable (block and cable provided) |
|
N1 |
(1) terminal block, line input neutral |
|
L1-L12 |
(12) terminal blocks, line power inputs |
|
SW1-SW12 |
(12) terminal blocks, switch channel outputs |
|
Note: Line power terminal blocks accept 10-14 AWG wire; torque to 4.43 lb-in (0.5 Nm); |
Controls & Indicators |
|
NET ID |
(2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID; |
|
SETUP |
(1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID |
|
OVR |
(1) Red LED and (1) miniature pushbutton for enabling override mode and saving override presets |
|
PWR |
(1) Green LED; solid illumination indicates line power is applied to N1 and L1; flashing indicates Cresnet power is supplied in absence of line power |
|
NET |
(1) Yellow LED; indicates communication with control processor |
|
RESET |
(1) Recessed miniature pushbutton, resets internal processor |
|
ON/OFF |
(12) Red LEDs and (12) miniature pushbuttons for individual manual channel activation |
Enclosure |
|
Surface mount module with (2) integral mounting flanges; mounts in a GLEP enclosure; (-LP) mounts in a GLEX enclosure |
Environmental |
|
Temperature |
32° to 104°F (0° to 40°C) |
|
Humidity |
10% to 90% RH (non-condensing) |
|
Heat Dissipation |
160 BTU/Hr |
Dimensions |
|
Height |
11.07 in (282 mm) |
|
Width |
9.5 in (241 mm) including mounting holes |
|
Depth |
4.78 in (121 mm) including standoffs |
|
Depth (-LP only) |
3.07 in (78 mm) |
Electrical Regulatory Certifications |
|
UL508, Section 41 (Endurance Test) and Section 61C (Electronic Ballasts) |
|
UL924, Emergency Power Equipment |
|
IEC60669-2-1, Section 19.102 (Contact mechanisms incorporated in electronic switches, intended for fluorescent lamp circuits or other capacitive loads) |
|
SCCR Rating - 18kA |
|
CE |