QuickMedia FlipTop Data Center, no keypad, black anodized
This product has been discontinued. Please contact Crestron True Blue Support at 1-888-CRESTRON for a replacement solution or more information.
- Stylish flush-mount FlipTop housing
- RGB/component input with stereo audio
- Dual-channel gated mic/line preamp
The QM-FTDC-NB provides an elegant multimedia interface specially designed to deliver extended connectivity for computers and tabletop teleconferencing equipment.
FlipTop Housing
Handsomely finished in either black anodized or brushed aluminum, the QM-FTDC-NB mounts flush in any tabletop surface for a clean, professional appearance. Wiring for the QM-FTDC-NB is extremely simple requiring just a single CresCAT™QM cable (sold separately).
Computer/Data Interface
Inputs are provided for one RGB/component signal with corresponding stereo audio to accept a connection from a computer or other high-resolution source. In addition, the QM-FTDC-NB includes two RJ11 and two RJ45 pass-thru connectors to accommodate phone, LAN, and other data signals. An AC power receptacle is also included.
Gated Mic Preamp
Two gated microphone inputs are included via terminal block connectors located below the table surface. Both dynamic and condenser type microphones are supported with software switchable 48V phantom power available at both microphone inputs. Balanced or unbalanced line-level sources such as wireless microphones can also be accommodated. Input gain and gating controls for each microphone/line input are fully adjustable at setup, and can also be controlled in real-time from a keypad or touchpanel.
QuickMedia® Transport
Using Crestron's revolutionary QuickMedia transport, all input signals are transmitted from the QM-FTDC to any QuickMedia Receiver or Distribution Center over a single inexpensive CAT5e type cable*. Computer resolutions up to 1920 X 1200 pixels at 60Hz are supported over cable runs up to 450 feet. Audio signals are transmitted digitally with high-performance 24-bit resolution. QuickMedia dramatically simplifies system design and installation, affording a higher level of performance at a lower overall cost.
MediaManager System Integration
Whether using just one FlipTop Box or several, complete system operation can be made transparent to the end-user with all signal routing occurring smoothly under the command of the MediaManager control system. Built-in video sensing can be utilized to trigger automatic input selection and power control. Complete MediaManager systems are easy to design, program and adjust from start to finish using Crestron SystemBuilder™ software.
Key Features
- Stylish flush-mount FlipTop housing
- RGB/component input with stereo audio
- Dual-channel gated mic/line preamp
- Video sensing | Auto-switching
- LAN and phone pass-thru ports | AC power outlet
- QuickMedia transport | Cresnet communications
- Low-cost, quick and easy installation
- Easy setup using Crestron SystemBuilder software
- Optional cable management kit
Video |
| Signal Types | RGB and component video† |
| RGB Formats | RGBHV, RGBS, or RGsB |
| Video/HDTV Formats | NTSC or PAL, HDTV up to 1080i/1080p† |
| Gain | 0dB (75 ohms terminated) |
| Maximum Resolution | 1920 x 1200 @ 60Hz (at unity gain) with maximum cable length of 450 feet and maximum compensation at receiver |
Audio |
| Features | stereo audio input, 2-channel gated mic preamp |
| Mic Input Gain | 0 to 100 % (40dB range) plus mute |
| Gate Level (Threshold) | 0 to 100 % |
| Attack | 0 to 100 mS |
| Decay (Release) | 0 to 5000 mS |
| A-D Conversion | 24-bit, 48 kHz |
| Frequency Response | 20Hz to 20kHz |
Buttons & Indicators |
| SETUP (bottom) | (1) miniature pushbutton and red LED, used for touch-settable ID (TSID) |
Connectors - Front Panel |
| COMPUTER | (1) DB15HD female; RGB(VGA)/component video† input; Formats: RGBHV, RGBS, RGsB, YPbPr; Input Impedance: 75 ohms; H/V Sync Impedance: 1k ohms; Maximum Input Level: 1 Vp-p; Maximum H/V Sync Level: 5 Vp-p; Signal sensing on H, Y, and Gs |
| AUDIO | (1) 3.5mm TRS mini phone jack; Unbalanced stereo line-level audio input; Maximum Input Level: 1 Vrms; Input Impedance: 10k ohms |
| LAN | (2) 8-pin RJ45 female, Ethernet LAN pass-thru jacks |
| PHONE | (2) 6-pin RJ11 female, Telephone pass-thru jacks |
| 125V | (1) Grounded AC socket, AC power pass-thru outlet; Maximum Load: 10 Amps @ 125 Volts AC, 50/60 Hz |
Connectors - Bottom Panel |
| MIC/LINE 1 - 2 | (2) 5-pin 3.5mm detachable terminal blocks; Balanced microphone/line inputs; Balanced Mic Input Level: -60 to -20 dBV nominal; Balanced Line Input Level: -28 to +12 dBV; 4 Vrms maximum; Unbalanced Line Input Level: -34 to +6 dBV; 2 Vrms maximum; Mic Input Impedance: 10k ohms, accepts 60 to 600 ohm source; Line Input Impedance: 22k ohms balanced, 11k ohms unbalanced; Phantom Power: 10 mA (total) @ 48 Volts DC, software enabled to both MIC inputs |
| LAN | (2) 8-pin RJ45 female; Pass through to front panel LAN jacks |
| PHONE | (2) 6-pin RJ11 female; Pass through to front panel telephone jacks |
| 125V | (1) 9 ft grounded AC line cord; Passes through to front panel AC power outlet |
| QM | (1) 8-wire RJ45 female, QuickMedia output port; Connects to QM input port of any QuickMedia device via CresCAT-QM or CresCAT-IM cable* |
| NET | (2) 4-pin 3.5mm detachable terminal blocks; Cresnet slave ports, paralleled; connect to Cresnet control network via CresCAT-QM or Cresnet cable |
| G | (1) 6-32 screw, chassis ground lug |
Power Requirements |
| Cresnet Power Usage | 8 Watts (0.33 Amp @ 24 Volts DC) |
Environmental |
| Temperature | 41° to 104°F (5° to 40°C) |
| Humidity | 10% to 90% RH (non-condensing) |
Enclosure |
| Black painted metal with black anodized or brushed aluminum cover; flush tabletop mountable |
Dimensions |
| Height | 5.39 in (13.69 cm) with lid closed |
| Width | 6.75 in (17.14 cm) |
| Depth | 5.71 in (14.50 cm) without mounting brackets |
Weight |
| 4.05 lbs (1.84 kg) |
* For QuickMedia wiring use CresCAT-QM, CresCAT-IM, or quality CAT5e/CAT6 cable with a delay skew of ≤15nS per 100m; the maximum aggregate cable length and delay skew between any QM transmitter (origination point) and QM receiver (endpoint) is 450 ft (137 m) and 22 nS; a maximum of two QM midpoint devices may be inserted in a given QM signal path; exceptions apply, refer to each respective product manual for full detail.
† Component video or HDTV may require a suitable VGA-to-component adapter or breakout cable, not provided.
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.