Products

    Pages

        CBLR2-HD

        FlipTop™ Cable Retractor, HDMI® to HDMI Cable

        Cable retractor for Crestron® FlipTop™ cable management systems.

        Photo shows model CBLR2-HD in horizontal orientation.

        Crestron® Cable Retractors offer a refined solution for Crestron FlipTop™ cable management systems. Each cable pulls out smoothly to a length of 3 f t (0.9 m ) and latches in position. A second pull of the cable releases the latch and retracts the cable back into the compartment.

        Each Crestron Cable Retractor features a patented mechanism that dampens the rate of retraction to prevent the cable from whipping as it pulls back into the FlipTop storage compartment. The retraction speed is installer adjustable to ensure full and effortless retraction without excessive force.

        Up to three, four, or six cable retractors may be installed depending on the FlipTop model . Spacer inserts are available to fill any unused cable retractor slots.1

        Cable retractors may be mounted vertically or horizontally . In the vertical position, the retractors hang straight down from the bottom of the FlipTop box allowing them to be hidden in a pedestal leg or similar space directly beneath the FlipTop. When positioned horizontally, the retractors project to the sides or front of the FlipTop, eliminating any obstruction near the floor.

        A 7 f t (2.1 m ) long tail is provided at the back-end of each cable retractor beneath the tabletop. This tail may be plugged into a wall plate or floor box, or connected to a DigitalMedia™ transmitter or similar interface device mounted under the table.

        Several models of cable retractors are offered to support HDMI®3, DisplayPort™2, VGA, stereo audio, USB, and CAT5e connectivity. The CAT5e model is suitable for Ethernet, HDBaseT®, and DigitalMedia 8G+® applications.

        CBLR2 series cable retractors may be installed in place of, or in combination with, existing 1st generation CBLR series cable retractors.3

        To configure a complete 600 Series FlipTop with your choice of finishes, cables, cable retractors, connector plates, and power outlets, use the online Crestron FlipTops Configuration Tool.

         
        Key Features
        • Connectivity for FlipTops™ cable management systems
        • Keeps interface cables at-the-ready
        • Eliminates hanging cable loops beneath the table
        • Cable pulls out smoothly to a length of 3 ft ( 0.9 m), and retracts by simply lifting it vertically above the table
        • Provides a 7 ft (2.1m) long tail below the table
        • Patented mechanism prevents cables from whipping while retracting
        • Models support HDMI® 2 , DisplayPort™ , VGA, stereo audio, USB, Ethernet, HDBaseT®, and DigitalMedia 8G+® connectivity
        • Vertical and horizontal mounting options accommodate most tabletop applications
        1. When installing fewer than the maximum quantity of cable retractors, a spacer insert is required to fill each unused cable retractor slot. For FlipTop 600 Series, use the FTA‑CBLRA‑INSERT‑2WIRE‑102. For all other FlipTops, use the CBLRA‑INSERT‑2WIRE or CBLRA‑INSERT‑BLANK. All spacer inserts are sold separately.
        2. The CBLR2‑HD model features active electronics and is designed for use as an input only. The source device must be connected to the pull-out end, and the sink device (e.g., the input of a display, monitor, transmitter, switcher, etc.) must be connected to the back end (labeled “TV” on the connector). The CBLR2‑HD has a minimum TMDS bandwidth of 10.2 Gbps and is capable of passing video signals up to 4K60 4:2:0 and 4K30 4:4:4 maximum.
        3. CBLR2 series cable retractors may be installed in place of, or in combination with, existing 1st generation CBLR series cable retractors, bearing in mind the following factors:
            a. The CBLR and CBLR2 series retractors have different latching and retraction mechanisms. Combining the different series within a single FlipTop housing may complicate end-user operation.
            b. For vertical installation, the CBLR2 series requires approximately 2 in. (50 mm) more vertical clearance below the mounting surface than the CBLR series.
            c. or horizontal installation, the CBLR2 series requires approximately 1.5 in. (38 mm) more horizontal clearance than the CBLR series. Please note that additional knee clearance may be required.
            d. For horizontal installations, the existing CBLRA‑BRKT‑H bracket may need to be repositioned.  The CBLRA‑BRKT‑H must be offset to one side of the existing CBLR retractors to allow clearance for the new CBLR2 retractors, which do not utilize the bracket themselves.
        4. Item(s) sold separately.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G+,  FlipTop, and FlipTops, are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries. DisplayPort and VESA are either trademarks or registered trademarks of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.

         
        FlipTop™ Compatibility
        Supported Bracket Supported Bracket
        CBLRA-BRKT-3-FT C2N-FTB-D, FT-PWR-D, QM-FTCC,
        QM-FTCC-NB, QM-FTDC,
        QM-FTDC-NB, QM-FTMC,
        QM-FTMC-NB, QM-FTMCSC,
        QM-FTMCSC-NB

        Fits up to 3 cable retractors.
        CBLRA-BRKT-4-FT C2N-FT-TPS4, C2N-FT-TPS4-U,
        FT-PWR-D-LG, QM-FTCC-TPS4

        Fits up to 4 cable retractors.
        CBLRAI-BRKT-4-FT FTI-PWR-D, QMI-FTCC, QMI-FTDC,
        QMI-FTMC, QMI-FTMCSC

        Fits up to 4 cable retractors.
        Bracket not required. FT-600, FT-TS600, FT-TSC600

        Fits up to 3 cable retractors on one side only.
        Bracket not required. FT-600, FT-TS600, FT-TSC600

        Fits up to 6 cable retractors.
        Bracket not available. IM-FTCC-M, IM-FTCCV-M,
        IMI-FTCC-M, IMI-FTCCV-M,
        QMI-FTCC-TPS4

        Retractors not supported.
        Available Cable Types
        CBLR2-HD Pull-Out End: HDMI Type A male 3 ft (0.9 m)
        Back End: HDMI Type A male 7 ft (2.1 m)
        CBLR2-MDP-DP Pull-Out End: Mini-DisplayPort male 3 ft (0.9 m)
        Back End: DisplayPort male 7 ft (2.1 m)
        CBLR2-VGA Pull-Out End: HD15 male 3 ft (0.9 m)
        Back End: HD15 male 7 ft (2.1 m)
        CBLR2-VGA-AUDIO (Unbalanced) Pull-Out End: HD15 male & 3.5 mm mini-TRS male 3 ft (0.9 m)
        Back End: HD15 male & 3.5 mm mini- TRS male 7 ft (2.1 m)
        CBLR2-AUDIO (Unbalanced) Pull-Out End: 3.5 mm mini-TRS male 3 ft (0.9 m)
        Back End: 3.5 mm mini-TRS male 7 ft (2.1 m)
        CBLR2-USB Pull-Out End: USB Type-A male 3 ft (0.9 m)
        Back End: USB Type-A male 7 ft (2.1 m)
        CBLR2-CAT5E
        (T-568B straightthrough, unshielded)
        Pull-Out End: RJ45 male 3 ft (0.9 m)
        Back End: RJ45 male 7 ft (2.1 m)
        Environmental
        Temperature 41° to 104°F (5° to 40°C)
        Humidity 10% to 90% RH (non-condensing)
        Enclosure
        Metal, black
        Dimensions
        Height 22.44 in. (570 mm)
        Width 1.12 in. (29 mm)
        Depth 4.00 in. (102 mm)
        See Additional Dimensions below for mounting variations
        Weight
        2.14 lb (970 g) each
        Compliance
        CE
        Additional Dimensions
        Dimensions include CBLR2 retractor, specified bracket, FlipTop Box with the lid closed, and required mounting brackets.
        Mounted vertically using CBLRA-BRKT-3-FT
        Height 25.00 in. (635 mm)
        Width 6.75 in. (172 mm)
        Depth 7.74 in. (197 mm)
        Mounted horizontally using CBLRA-BRKT-3-FT
        Height 9.27 in. (236 mm)
        Width 6.75 in. (172 mm)
        Depth 23.04 in. (586 mm)
        Mounted vertically using CBLRA-BRKT-4-FT
        Height 25.32 in. (644 mm)
        Width 7.67 in. (195 mm)
        Depth 8.40 in. (214 mm)
        Mounted horizontally using CBLRA-BRKT-4-FT
        Height 9.60 in. (244 mm)
        Width 8.50 in. (216 mm)
        Depth 23.61 in. (600 mm)
        Mounted vertically using CBLRAI-BRKT-4-FT
        Height 25.14 in (639 mm)
        Width 7.67 in. (195 mm)
        Depth 8.34 in. (212 mm)
        Mounted horizontally using CBLRAI-BRKT-4-FT
        Height 9.42 in. (240 mm)
        Width 7.67 in. (195 mm)
        Depth 23.68 in. (602 mm)
        Mounted vertically to both sides of a FlipTop 600 Series
        Height 25.29 in. (643 mm)
        Width 10.16 in. (258 mm)
        Depth 6.77 in. (172 mm)
        Mounted horizontally to both sides of a FlipTop 600 Series
        Height 9.48 in. (241 mm)
        Width 42.03 in. (1068 mm)
        Depth 6.77 in. (172 mm)
        Click here to search product certificates.
        1. When installing fewer than the maximum quantity of cable retractors, a spacer insert is required to fill each unused cable retractor slot. For FlipTop 600 Series, use the FTA‑CBLRA‑INSERT‑2WIRE‑102. For all other FlipTops, use the CBLRA‑INSERT‑2WIRE or CBLRA‑INSERT‑BLANK. All spacer inserts are sold separately.
        2. The CBLR2‑HD model features active electronics and is designed for use as an input only. The source device must be connected to the pull-out end, and the sink device (e.g., the input of a display, monitor, transmitter, switcher, etc.) must be connected to the back end (labeled “TV” on the connector). The CBLR2‑HD has a minimum TMDS bandwidth of 10.2 Gbps and is capable of passing video signals up to 4K60 4:2:0 and 4K30 4:4:4 maximum.
        3. CBLR2 series cable retractors may be installed in place of, or in combination with, existing 1st generation CBLR series cable retractors, bearing in mind the following factors:
            a. The CBLR and CBLR2 series retractors have different latching and retraction mechanisms. Combining the different series within a single FlipTop housing may complicate end-user operation.
            b. For vertical installation, the CBLR2 series requires approximately 2 in. (50 mm) more vertical clearance below the mounting surface than the CBLR series.
            c. or horizontal installation, the CBLR2 series requires approximately 1.5 in. (38 mm) more horizontal clearance than the CBLR series. Please note that additional knee clearance may be required.
            d. For horizontal installations, the existing CBLRA‑BRKT‑H bracket may need to be repositioned.  The CBLRA‑BRKT‑H must be offset to one side of the existing CBLR retractors to allow clearance for the new CBLR2 retractors, which do not utilize the bracket themselves.
        4. Item(s) sold separately.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G+,  FlipTop, and FlipTops, are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries. DisplayPort and VESA are either trademarks or registered trademarks of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.

        Pricing Region Select
        Please select your region below to see the appropriate Advertised Pricing.