iMedia Receiver with Video, three IM inputs


        This product has been discontinued. Please contact Crestron True Blue Support at 1-888-CRESTRON for a replacement solution or more information.

        • A simple, affordable solution for single-display multimedia presentation
        • Supports up to 3 IM transmitters
        • iMedia Transport for fast and easy single-cable installation

        For a substitute, please see IM-RX3 and IM-RXV3-M.

        Crestron's iMedia provides an extremely simple and affordable multimedia presentation solution for small conference rooms and training rooms. No comparable solution comes close to matching iMedia's speed and ease of installation, intuitive operation, and incredibly low cost.

        The iMedia Transport

        The iMedia transport utilizes a single CAT5e* type cable to transmit computer RGB, video, and stereo audio signals to a single projector or plasma display. A typical XGA signal (1024 X 768 pixels at 60Hz) can be transmitted up to 84 feet using iMedia, while higher resolutions up to 1600 x 1200 can be handled over shorter distances. Audio is transmitted digitally at 20-bit, 48 kHz resolution. Control and power signals are also contained on the same wire, eliminating the need for separate control or power cables.

        Three-Input iMedia Receiver

        Mounted at the projector or plasma display, the IM-RXV3 receives iMedia (IM) signals from up to three IM transmitters, breaking out the RGB, video, audio, and control signals for connection to the display device. Adjustable bandwidth compensation is provided on each IM input to maximize image quality over long cable runs.

        Integrated Audio

        The IM-RXV3 includes a built-in 20 watt stereo amplifier to drive a pair of 8 ohm speakers. Balanced line-level outputs are also provided to allow the audio signal to be connected directly to inputs on the display device or fed to a pair of powered speakers. Onboard digital signal processing affords adjustment of master volume, bass, treble and balance settings at setup.

        Display Control

        The IM-RXV3 contains both IR and bidirectional RS-232 ports to enable full control of the display device. Two relay ports are also included for control of a projection screen or lift. In addition, the four digital input ports can accept the direct connection of room occupancy sensors and power sensors for enhanced automation and monitoring.

        e-Control®2 and RoomView®

        Despite its simple design and low cost, the IM-RXV3 supports Crestron's powerful e-Control 2 XPanel and RoomView applications, delivering the industry's best help desk and resource management solution for any number of rooms equipped with iMedia.

        Fast, Easy Setup

        System setup takes mere minutes using iMedia Wizard software, providing easy start-to-finish configuration, adjustment, and documentation.

        Key Features
        • A simple, affordable solution for single-display multimedia presentation
        • Supports up to 3 IM transmitters
        • iMedia Transport for fast and easy single-cable installation
        • Supports XGA resolution up to 84 feet, UXGA maximum up to 34 feet
        • Supports composite video signals
        • Built-in LAN, RS-232, IR, relays and digital input control ports
        • Built-in 20W stereo amp and line outputs
        • Complete setup in minutes using iMedia Wizard Software
        • Built-in Web-server supports e-Control 2 and RoomView
          Gain 0dB (75 ohm termination)
          Formats RGBHV, RGBS, or RGsB
          Resolution 1024 x 768 @ 60Hz with maximum cable length of 84 feet, 1600 x 1200 @ 60Hz with maximum cable length of 34 feet; see manual for other resolutions
          Gain 0dB (75 ohm termination)
          Formats 480i (NTSC), 576i (PAL)
          D-A Conversion 20-bit, 48 kHz
          Bass/Treble Gain Range ±12dB
          Frequency Response 20Hz to 20kHz ±0.5dB (line), 20Hz to 20kHz ±1dB (speaker)
          S/N Ratio 82dB (line), 80 dB (speaker) 20Hz to 20kHz A-weighted
          THD+N 0.05% (line), 0.7% (speaker) 20Hz to 20kHz
          10/100BaseT, static IP or DHCP/DNS, auto-negotiating, built-in Web server, supports Crestron e-Control 2 XPanel and RoomView applications
        Connectors – Front Panel
          IM 1 - 3 (3) 8-wire RJ45 female, iMedia input ports;
        Connect to IM output ports of up to 3 iMedia transmitters via CresCAT-IM cable*
          AUDIO (1) 5-pin 3.5mm detachable terminal block;
        Balanced stereo line-level audio output;
        Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced;
        Output Impedance: 200 ohms balanced, 100 ohms unbalanced
          SPEAKER L – R (2) 2-pin 5mm detachable terminal blocks;
        Left and Right speaker-level audio outputs;
        Output Power: 10 Watts per channel;
        Minimum Impedance: 8 ohms
        Connectors – Rear Panel
          18VDC (1) 3-pin DC power jack (power supply included)
          RELAY OUTPUT 1 – 2, INPUT 1 – 4, G (1) 9-pin 3.5mm detachable terminal block comprising (2) normally open, isolated relays, and (4) digital input ports referenced to ground;
        Relay Rating: 2 Amp, 50 Volts AC/DC; MOV arc suppression;
        Input Rating: 0-24 Volts DC;
        Input Impedance: 2k ohms pulled up to 5 Volts DC;
        Input Logic Threshold: 2.5 Volts DC nominal
          IR (1) 3.5mm TRS mini-phone jack, IR output port;
        Connects to STIRP IR emitter probe (sold separately);
        IR output up to 1.2 MHz
          COMPUTER (1) 6-pin RJ11 female, computer console port
          LAN (1) 8-Wire RJ45 with 2 LED indicators
        10/100BaseT Ethernet port
        Green LED indicates link status
        Yellow LED indicates Ethernet activity
          COM (1) DB9 male, bidirectional RS-232 port;
        Up to 115.2k baud;
        Hardware and software handshaking support
          VIDEO (1) RCA female, composite video output;
        Output Impedance: 75 ohms;
        Output Level: 1 Vp-p nominal
          G (1) 6-32 screw, chassis ground lug
          RGBHV (1) DB15HD female, RGB output;
        Formats: RGBHV, RGBS, RGsB;
        Output Impedance: 75 ohms;
        Sync Impedance: 100 ohms;
        Maximum Output Level: 1 Vp-p maximum
        Sync Level: 5 Vp-p
          IM 1 - 3 (3) Screwdriver-adjustable bandwidth compensation (peak) adjustments
          SW-R (1) Recessed pushbutton for software reset
        LED Indicators
          PWR (green) Indicates power connected to 18VDC connector
          INPUT (red) Indicates activity on any input port
          IR (red) Indicates activity on IR port
          COM (red) Indicates activity on COM port
        Power Requirements
          IM-RXV3 54 Watts (3 Amps) @ 18 Volts DC
          PW-1830RU Power Supply (included) <1.6 Amps @ 100-240 Volts AC
          Temperature 41° to 104°F (5° to 40°C)
          Humidity 10% to 90% RH (non-condensing)
          Black metal; freestanding, surface mount using "L" brackets provided, or pole mount using optional pole mount kit (sold separately)
          Height 1.61 in (4.08 cm)
          Width 8.75 in (22.23 cm)
          Depth 7.69 in (19.53 cm)
          1.75 lbs (0.80 kg)

        * For iMedia use CRESCAT-IM cable, or quality CAT5e/CAT6 cable having a maximum delay skew of 15nS per 100m.

        Click here to search product certificates.
        Pricing Region Select
        Please select your region below to see the appropriate Advertised Pricing.