Connectors: |
| NET | (1) 6-wire RJ-type connector and (1) 4-pin male connector; for expansion to Cresnet or SmarTouch peripherals; 50W maximum load depending on expansion slot load |
| Relays | (8) normally open, isolated relays; each relay is rated 1A, 30VAC/DC; MOV arc suppression across contacts for use with "real world" loads |
| Input/Output | (8) programmable digital/analog inputs and digital outputs; digital outputs offer 250mA sync from maximum 24VDC; catch diodes for use with "real world" loads; digital inputs rated for 0-24 VDC, 20K ohms input impedance, logic threshold 1.25VDC; analog inputs rated 0-10VDC, protected to 24VDC maximum, 20K ohms input impedance; programmable 2K ohms pullup resistor (per pin, software reference to GND or closure to GND) |
| IR/Serial | (8) serial outputs for (IR), RS-232 or serial interface; signal (S) and ground (G) pins; infrared output up to 1.2MHz, serial protocols incluse RS-232 with speeds up to 115,200 baud. |
| COM | (6) bidirectional serial ports for RS-232, RS-422 or RS-485 communication with hardware and software handshaking; speeds up to 115,200 bps |
| Computer | (2) one per front and rear panel, 9-pin DB9 female connector for programming with a PC; modem compatible; null modem cable not included |
Expansion Slots |
| DPA | Direct Processor Access expansion slot for optional local area network (LAN) interface card; (LAN) interface card accepts CNXENET or CNXENET+ card, which require field installation and has (1) 8-wire RJ45 connector for communication access |
| Other (1-3) | (3) open "card cage"slots accept any CNX expansion cards |
LED Indicators |
| PWR | Indicates power supplied to the unit |
| NET | Indicates activity within the system |
| ERR | Indicates an error message is available from the software feature buttons |
| TXD (Ethernet) | Indicates transmission of ethernet data |
| RXD (Ethernet) | Indicates reception of ethernet data |
| LNK (Ethernet) | Indicates attachment to ethernet network |
| ERR (Ethernet) | Indicates ethernet protocol error |
| COM TX (A-F) | Indicates transmission of data to serial devices attached to respective COM ports |
| COM RX (A-F) | Indicates reception of data from serial devices attached to respective COM ports |
| COM RTS (A-F) | Indicates when unit is ready to receive data from serial devices attached to respective COM ports |
| COM CTS (A-F) | Indicates when serial device on the respective COM port is ready to accept data from the unit |
| IR-Serial (A-H) | Indicates activity on respective IR/SERIAL line |
| Input-Output (1-8) | Indicates input voltage threshold for respective I/O port exceeded |
| Relay (1-8) | Indicates respective relay is closed |
| Slot (1-3) | Illuminates when card is inserted into slot; flashes when card is active |
Reset Buttons |
| HW-R | permits physical reset of system |
| SW-R | Depress in combination with the HW-R button to perform an overload/reset |
Screen |
| (1) reverse mode (yellow and black) LCD back light; (2) lines, (40) characters per line |
Menu Function Buttons |
| Panel | Programmable interface offering command text, indirect text, and hierarchical screen structure |
| Info | Displays system information including the loaded SIMPL program |
| MSG | Displays system alarms and error messages |
| Time | Permits alterations to system date and time; access code required |
| COM | Monitors the transmission and reception traffic on each COM port |
Menu Selection Buttons |
| Menu | Returns screen display to menu default state |
| ^ | Scrolls listed information up |
| V | Scrolls listed information down |
| BKLT | Adjusts LCD backlight and LED indicator brightness |
Power Requirements |
| 100-250VAC, 2.3A, 50/60Hz, internal universal power supply |
Dimensions |
| 3.47" / 8.81cm (H) x 19.00" / 48.26cm (W) x 8.43" / 21.41cm (D) |
Weight |
| 7.01lbs / 3.18kg |
to search product certificates.