GLX-HSW8

8 Channel High-Inrush Switch Module

Material Number: 6501457

Discontinued

This product has been discontinued. Please contact Crestron True Blue Support at 1-888-CRESTRON for a replacement solution or more information.

Replace With GLXP-HSW12-LP

  • 8 channels of high-inrush power switching
  • Compatible with lighting and motor loads
  • Supports 100 to 277 Volt applications

Visit the Crestron® Lighting Fixture Compatibility page to find out which Crestron lighting devices have been tested and are compatible with third party lighting fixtures.

The GLX-HSW8 High-Inrush Switch Module for Crestron Green Light® Architectural Dimming Cabinets features eight channels of high-inrush switching. The module is part of a complete Crestron engineered GLPD Green Light dimming panel.

For more information on Crestron Green Light commercial lighting products, please contact Crestron Sales Support Services.

 
Key Features
  • 8 channels of high-inrush switching
  • Compatible with lighting and motor loads
  • Supports 100 to 277 Volt applications
  • 16 Amp load rating per channel
  • Arc-less switching
  • Positive air gap at each output
  • Phase-independent channels
  • Cresnet® communications
  • Redundant power capability—module powered via line or Cresnet
  • Local controls for testing and verification
  • Local and remote override capability
  • Non-volatile power failure memory
  • GLE cabinet installation
  1. Line power terminal blocks accept 10-26 AWG wire; torque to 5.31 lb-in (0.6 Nm).

Crestron products may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

The specific patents that cover Crestron products are listed online at: patents.crestron.com.

Certain Crestron products contain open source software. For specific information, visit www.crestron.com/opensource. 

Crestron, the Crestron Logo, Crestron Green Light, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice.  ©2015 Crestron Electronics, Inc.

 
CrestronHome
Load Ratings
  Dimmer Channels 8
  Per Channel 16 Amps at 100 to 277 Volts AC, 50/60 Hz;
0.5 HP at 120 Volts, 1 HP at 230 Volts, 1 HP at 277 Volts
  Switch Load Types Incandescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, fluorescent ballast, high-intensity discharge, motor, LED driver
  Relay Lifetime 1,000,000 on/off operations at full electronic ballast load
Power Requirements
  Primary 100-277 Volts AC, 50/60Hz, supplied via channel 1 (L1, N1)
  Secondary (Optional) 5 Watts at 24 Volts DC, supplied via Cresnet®
Connectors
  NET (2) 5-pin headers;
Connect to adjacent module or internal connecting block using interconnect cable (block and cable provided)
  N (1) Terminal block, line input neutral
  L1-L8 (8) Terminal blocks, line power inputs[1]
  SW1-SW8 (8) Terminal blocks, switch channel outputs
Controls & Indicators
  NET ID (2) 7-segment green LED digits and (2) miniature pushbuttons, set Cresnet ID
  SETUP (1) Red LED and (1) recessed miniature pushbutton, enables Setup mode and sets touch-settable ID
  OVR (1) Red LED and (1) miniature pushbutton, enables override mode and saves override presets
  PWR (1) Green LED, indicates power status;
Solid illumination indicates line power is applied to N and L1;
Flashing indicates Cresnet power is supplied in absence of line power
  NET (1) Yellow LED, indicates communication with control processor
  RESET (1) Recessed miniature pushbutton, resets internal processor
  ON/OFF (1) Red LED and (2) miniature pushbuttons per each channel, manually activate channels
Enclosure
  Surface mount module;
Mounts in a GLE enclosure
Environmental
  Temperature 32° to 104° F (0° to 40° C)
  Humidity 10% to 90% RH (non-condensing)
  Heat Dissipation 112 BTU/Hr
Dimensions
  Height 14.50 in (368 mm)
  Width 6.00 in (152 mm)
  Depth 3.22 in (82 mm)
Weight
  5.0 lbs (2.27 kg)
Electrical Regulatory Certifications
  UL508, Section 41 (Endurance Test) and Section 61C (Electronic Ballasts)
  UL924, Emergency Power Equipment
  IEC60669-2-1, Section 19.102 (Contact mechanisms incorporated in electronic switches, intended for fluorescent lamp circuits or other capacitive loads)
  SCCR Rating - 65kA
  CE
Click here to search product certificates.
  1. Line power terminal blocks accept 10-26 AWG wire; torque to 5.31 lb-in (0.6 Nm).

Crestron products may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

The specific patents that cover Crestron products are listed online at: patents.crestron.com.

Certain Crestron products contain open source software. For specific information, visit www.crestron.com/opensource. 

Crestron, the Crestron Logo, Crestron Green Light, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice.  ©2015 Crestron Electronics, Inc.

Pricing Region Select
Please select your region below to see the appropriate Advertised Pricing.